Configurator - which version - Comfigurator 2.X - Software Applications - Comfort Home Automation/ Security System Forums

Comfort Home Automation/ Security System Forums Home

Comfort Home Automation/ Security System Forums > Software Applications > Comfigurator > Comfigurator 2.X > Configurator - which version

Configurator - which version

Moderated by: admin

New Topic

Printer Friendly

Rate Topic

Author	Post

Posted: Saturday Mar 14th, 2009 09:46 pm

Quote

1^st Post

bbc
Member

Joined:	Saturday Mar 14th, 2009
Location:
Posts:	4
Status:	Offline

Hi

My comfort system is about 7 years old. In the past I used configurator to configure. But I've forgotten what version etc.

So - what version of configurator so I need and do I need to upgrade my comfort ?

I have the original license key and it seems to work in v1.6.10 (the interface looks like the version I used to use).

Thanks

Bill

Last edited on Saturday Mar 14th, 2009 09:53 pm by bbc

Posted: Sunday Mar 15th, 2009 02:47 am

Quote

2^nd Post

ident
Administrator

Joined:	Wednesday Aug 9th, 2006
Location:	Singapore
Posts:	1416
Status:	Offline

You should be able to use Comfigurator 3 for your Comfort I system. However this software has had limited testing in Comfort I
You can also continue to use 1.6 if that suits you. The later versions of Comfigurator do not require a licence
If you intend to continue to make changes in programming, perhaps you should consider upgrading to Comfort I, see http://www.comfortforums.com/forum25/1403.html for the upgrade package announcement which shows the improvements over Comfort I

Posted: Sunday Mar 15th, 2009 07:38 pm

Quote

3^rd Post

bbc
Member

Joined:	Saturday Mar 14th, 2009
Location:
Posts:	4
Status:	Offline

Thanks

When I start v1.6 it shows a drop down asking which file format I want to use (Pro/Ultra etc.) What should I choose to work with my Gen 1 comfort ?

Also - I've mislaid my old ccl(?) files, can I load it from comfort (I seem to recall this wasn't practical as I'd lose all the zone names etc.)

Thanks again.

Bill

Posted: Monday Mar 16th, 2009 02:51 am

Quote

4^th Post

leonchue
Cytech

Joined:	Monday Aug 7th, 2006
Location:	Singapore
Posts:	36
Status:	Offline

Check your main board's U1 IC. If it is "Outside" version, then use Pro. If it is "Action" version, then use Ultra.

Also - I've mislaid my old ccl(?) files, can I load it from comfort (I seem to recall this wasn't practical as I'd lose all the zone names etc.)

Yes. You are right about losing the names.

Posted: Monday Mar 16th, 2009 11:10 am

Quote

5^th Post

bbc
Member

Joined:	Saturday Mar 14th, 2009
Location:
Posts:	4
Status:	Offline

Hi

How do I check "outside" etc. - I'm not an installer just a user, I've made some changes on the panel before so If you can tell me what to look for that would be great.

Can I check this using the original ccl file (I found it

). When I open it I get an error "Invalid Keyword - UseBranhActions specified"

So I assume I'll be OK once I set configurator to the right value for Pro/Ultra ?

Bill

Posted: Monday Mar 16th, 2009 11:54 am

Quote

6^th Post

bbc
Member

Joined:	Saturday Mar 14th, 2009
Location:
Posts:	4
Status:	Offline

Also - to use the old ccl file I have, do I need to do anything with the file version (I see an option in the file menu). I assume my older file with v1.6 will be fine ?

Posted: Monday Mar 16th, 2009 06:05 pm

Quote

7^th Post

ident
Administrator

Joined:	Wednesday Aug 9th, 2006
Location:	Singapore
Posts:	1416
Status:	Offline

You probably have Comfort I Pro . The label on the U1 IC should be "O4.xxx" where xxx is the revision The bottom right of your status bar should show File System 18
You dont need to make any changes to the ccl file
If you have problem using 1.6 then try 2.23

Current time is 12:40 pm

Comfort Home Automation/ Security System Forums > Software Applications > Comfigurator > Comfigurator 2.X > Configurator - which version

Top