| Posted: Tuesday Jul 7th, 2020 11:19 am |
|
1st Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Hi,Since upgrading comfigurator to version 3.13.3.0 a few weeks ago i cannot connect to the UCM when i search for modules. I have checked the settings and IP addresses are all correct and the comfort server manager sees the UCM. Any ideas?????Ray Attachment: Capture.PNG (Downloaded 56 times)
|
| Posted: Tuesday Jul 7th, 2020 12:48 pm |
|
2nd Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
Please check if the D9 red and D10 green leds on the UCM baseboard are blinking which shows the UCM is being polled by Cofort
|
| Posted: Tuesday Jul 7th, 2020 01:40 pm |
|
3rd Post |
| Posted: Tuesday Jul 7th, 2020 02:19 pm |
|
4th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Yes both led are flashing.
|
| Posted: Wednesday Jul 8th, 2020 03:11 am |
|
5th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
do you have ETH02 or ETH03? What is your ucm firmware?
|
| Posted: Wednesday Jul 8th, 2020 08:20 am |
|
6th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Hi,
I installed an ETH03 after the last fault and the firmware version is 7.119.
Ray
|
| Posted: Friday Jul 10th, 2020 01:33 pm |
|
7th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
Please check comfort server manager status.Can you see the eth03 ipaddress in the window?
|
| Posted: Friday Jul 10th, 2020 02:12 pm |
|
8th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Yes it address is OK and it is blue.
|
| Posted: Saturday Jul 11th, 2020 03:31 am |
|
9th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
In CS Manager the state is idle if there is no connectionWhen you try to connect, it should change to Busy. Can you check that. Also for the 2nd portOf it is busy then the PC has managed to connect..
Have you tried another pc?
|
| Posted: Sunday Jul 12th, 2020 06:47 pm |
|
10th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Hi,System stays in IDLE state all the time.Don't have another PC to try this on.Ray Attachment: Capture.PNG (Downloaded 37 times)
|
| Posted: Monday Jul 13th, 2020 03:34 am |
|
11th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
Cab you reset the ETH03 (not UCM) by pressing the RESET button on the ETH03 submodule.
The Idle should change to Busy when you connect to it by Comfigurator.
If nothing changes try to re-upgrade the ETG03 firmware to the same 2.2.3 see this link http://www.comfortforums.com/forum113/3820.html
|
| Posted: Monday Jul 13th, 2020 09:10 am |
|
12th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Hi,Pressed the reset on the sub module but nothing seemed to happen.Upgraded the firmware to 2.2.3 as requested.Upgrade was successful.Retried to scan modules but getting same message.Ray
|
| Posted: Monday Jul 13th, 2020 12:43 pm |
|
13th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
This is a puzzle. You are able to upgrade the ETH03 firmware so you should be able to connect to the ETH03 network port.
But the ETH03 status in CS Manager remains as IDLE when you try to connect which means it is not able to connect to the network port. It seems to be contradictory.
Can you check what is the serial number printed on the UCM?
|
| Posted: Monday Jul 13th, 2020 01:56 pm |
|
14th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Hi Slychiu,Really don't understand as all looks OK and nothing has changed but there is no connection.See attached for serial number as requested.Ray Attachment: UCM Serial Numver.jpg (Downloaded 32 times)
|
| Posted: Tuesday Jul 14th, 2020 03:11 am |
|
15th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
Ray, that serial number belongs to a UCM/ETH02 from 2011.
You changed to ETH03 Do you have the serial number f the eth03 submodule, it should be on the eth03 itself
The red D9 appears to be off although it is a still photo. does it still bllink?
Do you think you can manage to take a video of the whole ucm at the same time that you press log in?
|
| Posted: Tuesday Jul 14th, 2020 08:44 am |
|
16th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
Slychiu,Yes the D9 is still flashing.The serial number on the small board that the network cable connects to is C095296The video was taken as Comfigurator was trying to scan for modules.How do you want me to send the video?Ray Attachment: 20200714_083058.jpg (Downloaded 31 times)
|
| Posted: Tuesday Jul 14th, 2020 08:46 am |
|
17th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
Please send to support@cytech.biz
|
| Posted: Tuesday Jul 14th, 2020 08:55 am |
|
18th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
also check that you do not have 2 UCMs with the sane ID That would prevent the ucm from logging in although D9 would blnk
|
| Posted: Tuesday Jul 14th, 2020 09:13 am |
|
19th Post |
raygregg114
Member
| Joined: | Tuesday May 4th, 2010 |
| Location: | |
| Posts: | 104 |
| Status: |
Offline
|
back to top
|
just sent Dropbox link to email address
|
| Posted: Tuesday Jul 14th, 2020 09:28 am |
|
20th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
I cannot see any proble with the videoDo you have another UCM? it may be possible that the ID of this or another UCM is wrong due to a loose connection on the ID headers so the ID has a conflict even thoug D9 led is blinking
Can you temporarily disconnect any other UCM and try again
|
| Current time is 10:03 am | Page: 1 2 3   |
|
