Wifi01 Submodule - Printable Version +- Comfort Automation/ Security System Forums (https://www.comfortforums.com) +-- Forum: Products (https://www.comfortforums.com/forum-3.html) +--- Forum: UCMs (https://www.comfortforums.com/forum-146.html) +---- Forum: UCM/Wifi (https://www.comfortforums.com/forum-141.html) +---- Thread: Wifi01 Submodule (/thread-5243.html)

- slychiu - 10-31-2020 Wifi01 is a sub-module which plugs in to UCM06,  CM9001, LGX01 or UCM/Logic which connects to a wifi Access Point for programming by Comfigurator or for use by the Cytech mobile apps. Wifi Specifications Wifi Standards: 802.11 b/g/n Frequency Band 2.4 GHz, Channels 1-13 Protocols/Profiles UDP, TCP, ICMP, DNS, HTTP(S), DHCP, SMTP, SNTP, OTA Security  – Open, WEP, WPA, WPA2-PSK Comms Range > 330m line of sight (λ/4 antenna)  RF Transmit Power +19dBm (11b), +16dBm (11g), +14dBm (11n) RF Receive Sensitivity -94dBm (11b/g), -90dBm (11n) Operating Temp. -40°C to +85°C Certifications FCC, CE, IC CM9001/UCM Features Single wifi IP Adddress and Port (ETH03 has 2 ports) in Server Node Higher speed data transfer 38400 baud than USB or ETH03 (9600 Baud). Wifi01 plug in to CM9001 wil have the highest speec as there is no RS485 bus involved. Network Date/Time Update every day with Daylight saving time correction. Current < 100 mA Comfigurator Read/Write, Upgrade Firmware, Upgrade Vocabulary Access by Cytech iOS/Android Apps Ordering Information Wifi01 can be ordered by itself to be plugged in CM9001 or UCM06, or it can be ordered as UCM/Wifi01 (UCM06 + Wifi01) The Wifi01 package includes Wifi01 submodule WA02-0004 Antenna with MMCX connector 2 x M3 screws and standoffs System Requirements CM9001  firmware 7.173 (Wifi01 plugged in CM9001) UCM 7.137 (Wifi01 plugged in UCM06) Comfigurator Version 3.13.5 and above to set up Wifi01 in Options > Settings Buttons  RESET - Reset Wifi01 Module  SOFT - Soft AP Button ( See Instructions below)  FRST:  Factory Reset. (See Intsructions below) LED Indicators  TXW (Red) - Blinks when data is transmitted to Wifi  RXW ( Green) - Blinks when data is Received from Wifi  IP (Green) - Fast Flash when Wifi01 is not in network, Slow Flash when network is joined  Soft AP (Red) - Flashes when in Soft AP mode, Off when in Normal Station Mode The Wifi01 Manual can be downloaded from https://www.cytech.biz/wifi01_submodule.html - slychiu - 10-31-2020 Connections to UCM06 and CM9001 If the Wifi01 has been purchased separately, remove the CM9001 or UCM06 from the enclosure and screw in the 2 standoffs withnuts from the back of the CM9001 or UCN06 PCB so that Wifi01 can be plugged in on top of the PCB. If using with UCM06, remove any submodule eg USB01 or ETH03 from UCM06 before mounting Wifi01 Plug Wifi01  into the 10 way female connector on UCM06 or CM9001 and screws in to the threaded standoff Plug the antenna into the MMCX connector on Wifi01. The Antenna should be mounted outside the CM9001 Metal enclosure. The Wifi01 and Enclosure should be mounted in a location that is able to access Wifi. For UCM/Wifi, set up the ID on the UCM Base Board (Refer to UCM Manual). For CM9001, ID is not required . - slychiu - 10-31-2020 Using Comfigurator Use  Comfigurator software 3.13.5  or above to configure Wifi01. Download from  https://www.cytech.biz/comfigurator.html Go to Menu >  Options > Settings > UCM Interface and select Wifi from the drop-down list as shown below.  Select Wifi and click on Wifi Configuration. Fill in the fields required  Wifi SSID: The SSID of your wifi access point. [color=\"#ff0000\"](Spaces are not accepted in Comfiguratot 3.13.6)[/color]  Wifi Passkey: The passkey of your wifi access point [color=\"#ff0000\"](Spaces are not accepted in Comfiguratot 3.13.6)[/color]  Static IP Address: enter a static IP address to be assigned to Wifi01  Netmask: eg 255.255.255.0  Gateway: IP address of yur router or gateway eg 192.168.0.1  TCP Server Port: Port used for Wifi communications in Server Mode eg 3000  Client Mode: No for normal use. Client Mode is used for Universal UCM  Time Zone: Enter Time zone in hours for UTC.This is for Internet Time update  NTP Server: This is the time server which supplies the Internet time to Wifi01. Leave it at the default unless otherwise instructed. Wifi01 will update the Date and Time to CM9001 every day. Go to Comfigurator  Schedule > Sunrise/Sunset Times, Sunrise/Sunset Properties and  set up your City/Location. This allows CM9001 to handle Daylight Saving Times correctly. Press the Wifi Setup button . The following screen appears. Follow the instructions by pressing the buttons on the Wifi01 PCB Soft AP mode allows your computer to make an initial connection to Wifi01 so that the Wifi01 settings can be written to it.  In Soft AP mode the red SOFTAP LED will flash, as well as the Green IP LED..  Look for the SSID eg Gecko OS Web Setup xxxxx, and connect to it.  Enter \"password\" when asked for the passkey  When connected to the Soft AP SSID, press OK. If succesful, you should see the screen below. Press OK to acknowledge.  Press \"Copy to Clipboard\" if there is a problem, to investigate the setup. Send to support@cytech.biz for assistance if necessary. After pressing OK, Soft AP mode is disabled and the Soft AP SSID should no longer be seen. The Soft AP Mode is ended, and the Wifi01 will be a station on the Wifi network On the Wifi01, the green IP LED should flash slowly if it has joined the network. It will blink fast if the Wifi01 is not part of any network. If necessaey press the RESET button on Wifi01 On the Wifi01, the green IP LED should flash slowly if it has joined the network. It will blink fast if the Wifi01 is not part of any network. If necessaey press the RESET button on Wifi01. - slychiu - 10-31-2020 After setup is completed, you can see the Wifi IP address as shown below. In the Wifi Configuration Screen, \"Read Wifi \" button reads the wifi settings from Wifi01, if it has been set up. \"RSSI\" is a Read only field that shows the Wifi signal strength. \"Write Wifi\" writes the changed settings to Wifi01. - slychiu - 10-31-2020 UCM/Wifi01 For UCM/Wifi01, Modules Tab> Scanning for Modules will show UCM and its properties in the UCM section. - slychiu - 10-31-2020 CM9001 with Wifi01 If Wifi01 is mounted on CM9001, Modules Tab> Scanning for Modules will show UCM properties as part of Controller Properties instead of in the UCM section - slychiu - 10-31-2020 Factory Reset Factory Reset is performed by Pressing and holding FRST for at least 10 seconds while  pressing RESET momentarily before  releasing FRST. TXW, RXW blinks when done. Do not do this unless instructed by Cytech Technical Support. Troubleshooting Notes The Wifi01 module is detected by UCM06 or CM9001 at Power On. Resetting the CM9001 or  UCM does not reset the Wifi module so that the wifi connection is not diconnected during a System Reset. If Comfigurator cannot connect to the Wifi01 module (\"Unable to connect to UCM\" message), press the Reset button on Wifi01. Note that the message \"Incorrect Login Code\" does NOT mean that Wifi01 is not connected - it means the User Code is incorrect. To Reset the Wifi Module, press and release the RESET button on the Wifi01. Do not remove or plug in the Wifi01 from CM9001 or UCM06 with power on. Always turn off power before removing or plugging in Wifi01. - slychiu - 11-03-2020 Wifi01 can also be plugged in to LGX01 Logic Engine and UCM/Logic Controller without I/O - slychiu - 05-30-2021 Wifi Time-out Configuration > Modules and Settings > Miscellaneous Seetings > Wifi Idle Timeout determines the time out (in minutes) when there is no communication from the wifi side. The UCM will log out after this timeout. Default is 5 minutes. Write to Comfort to change this setting