Comfort Automation/ Security System Forums > Third Party (interfacing to Comfort) > KNX (EIB) > 2nd generation UCM/KNX Interface |
Moderated by: admin | Topic closed |
Author | Post | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
admin Administrator
|
The UCM/KNX has been replaced by UCM/KNX2, which is a more advanced KNX interface, see http://www.comfortforums.com/view_topic.php?id=4470&forum_id=12&jump_to=20570#p20570 Cytech is pleased to announce that we have developed a 2nd generation KNX interface, which we call UCM/KNX to distinguish from the current UCM/EIB. The UCM/KNX will be similar to the UCM/EIB but will have an Nonvolatile EEPROM in U2 to hold the configuration data. This will be much more closely integrated with KNX than before. The UCM/KNX interface allows the alarm system to be fully visible on KNX; the status of alarms and which doors, windows or motion sensors are activated, and whether the security system is set or unset are mapped to assigned group addresses. It allows KNX switches and input devices to send commands to Comfort to bypass zones, or to control outputs or other devices. A KNX touchscreen can be used to set and unset the security system by entering the user code, just like a physical keypad. Instead of mapping group addresses to Counters by shunts, there will be a software configuration which is part of Comfigurator 3 to map Group addresses to Comfort. This makes it easy to program Comfort to interface with KNX, without requiring a lot of knowledge of Comfort. Comfigurator 3.18 and above is required to support KNX software configuration. The screen below shows UCM/KNX Properties page. The UCM/KNX can be assigned any valid Physical address, hence several UCM/KNX can be used in the same system to connect to a single KNX system, or with several independent KNX systems The screenshot below shows KNX to Comfort Page which maps KNX Group addresses to Comfort In the KNX to Comfort page, you can
The screenshot below shows the Comfort to KNX page where Comfort zones, alarms, and other events are mapped to KNX group addresses
Monitor Mode allows received KNX telegrams to be displayed The new UCM/KNX allows KNX integrators to interface with Comfort without having to program Responses, ie they dont need to know very much about Comfort. It is a very powerful tool for Comfort to KNX Integration See UCM/KNX on the Cytech website at http://www.cytech.biz/knx_interface.html The UCM/KNX Manual can be downloaded from http://www.cytech.biz/ucmknx_manual.htm This should make Comfort an even more powerful proposition for KNX partners Last edited on Thursday Jul 18th, 2019 03:03 am by |
|||||||||
TheMax74 Member
|
Good news. Thank you. |
|||||||||
slychiu Administrator
|
The version of Comfigurator, 3.1.8 which supports the UCM/KNX is available, Last edited on Saturday Apr 3rd, 2010 07:55 am by |
|||||||||
TheMax74 Member
|
Thanks for the infos. Already downloaded 3.0.8 and new KNX firmware. I'm waiting for delivery of the UCM from cytechdirect. Last edited on Wednesday Jul 22nd, 2009 09:42 am by TheMax74 |
|||||||||
TheMax74 Member
|
UCM/EIB arrived. It has the U2 socket EEPROM on board, below the "reset" pushbutton, so i think is the new version and i don't need to upgrade any hardware. As i can read from the ucmknx draft manual, my Ultra II firmware is ok (5.164), but my UCM05 isn't (5.156). If i don't perform the "scan for ucm", is it mandatory to upgrade my UCM05 to a newest firmware ? Thanks. |
|||||||||
slychiu Administrator
|
You need UCM 5.178 to support the writing of comfiguration into the UCM/KNX from Comfigurator, as the older UCM does not have this function If you dont have another UCM05 to upgrade it, we can do it for you for the cost of transport. Otherwise perhaps another user on the forum with a UCM which needs upgrading may be able help you out as both UCM05s can be upgraded if one of you sends the UCM to the other |
|||||||||
TheMax74 Member
|
I have another old UCM05. I will use this to upgrade my UCM/ETH. Thanks. |
|||||||||
admin Administrator
|
Please note the download links for the firmware below The UCM/KNX firmware can be downloaded from http://www.cytech.biz/ucmknx_firmware.html UCM 5.192 is the minimum UCM05 firmware which is required to work with UCM/KNX The latest UCM/USB, UCM/Ethernet, UCM/232 firmware can be downloaded from http://www.cytech.biz/ucm_firmware.html The current Comfigurator software which supports the UCM/KNX can be downloaded from http://www.cytech.biz/comfigurator.html Last edited on Monday Apr 18th, 2011 10:31 am by |
|||||||||
slychiu Administrator
|
The UCM/KNX is now officially released, please visit the download links highlighted below Firmware version minimum = KNX 5.195 UCM05 Firmware minimum = UCM 5.192 Comfort Firmware minimum = ULT 5.172 Comfigurator 3.2.4 and above Last edited on Monday Apr 18th, 2011 10:34 am by |
|||||||||
TheMax74 Member
|
Well, great job. No more problems with KNX 192 in the past two weeks. |
|||||||||
slychiu Administrator
|
Thats good. There were some minor bugs with 5.192 including the Read from Group Aggress that you reported. This has been fixed so you should upgrade to the new version |
|||||||||
mrtae Member
|
Chiu, Just FYI... The link you provide below is point to UCM05 latest firmware. Comfort Firmware minimum = 5.164 but ULT 5.169 is the latest So the Comfort firmware ULT5.169 is an official release? Last edited on Monday Aug 17th, 2009 01:15 am by admin |
|||||||||
slychiu Administrator
|
The link is incorrect and will be corrected in the next few days. There is a problem with our servers currently This topic shall be closed in order to prevent it from getting too long Please post a new topic if you have any questions, comments or problems Last edited on Monday Apr 18th, 2011 10:34 am by |