Comfort Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register
Comfort Automation/ Security System Forums > Support > Problems & Troubleshooting > Firmware Upgrading Problems > Firmeware update

Firmeware update
 Moderated by: ident
 New Topic   Reply   Printer Friendly 
 Rate Topic 
AuthorPost
 Posted: Tuesday Mar 27th, 2012 11:05 pm
   PM  Quote  Reply 
1st Post
Canha
Member
 

Joined: Wednesday Mar 23rd, 2011
Location:  
Posts: 30
Status: 
Offline

  back to top

Hi

I have a UCM/Eth and a UCM/RS232. I want to upgrade the firmeware of both UCM but I have two problems.

The UCM/Eht has a 5.192 firmeware and th UCM/RS232 has 5.128. I can't upgrade the UCM/Eht because the firmeware of the UCM/RS232 is too old. When I do the "Scan for all modules" with only these two modules, this is what is shown (picture below). It show's that the UCM/RS232 is a CWM. Is this possible?

Now, I can't upgrade the UCM/Eth because I can't upgrade the UCM/RS232.

Any ideas?

Thanks

Avelino Canha

Attachment: Sem Título3.png (Downloaded 85 times)


 Posted: Wednesday Mar 28th, 2012 01:53 am
   PM  Quote  Reply 
2nd Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

That is strange
I will contact you by Private mail to give instructions


 Posted: Wednesday Mar 28th, 2012 01:15 pm
   PM  Quote  Reply 
3rd Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

Actually I think you can use UCM/ETH 5.192 to upgrade the firmware of UCM 5.128 to the latest UCM 6.012 using the programming cable as shown in http://comfortforums.com/forum4/1782.html

can you give it a try?


 Posted: Wednesday Mar 28th, 2012 02:15 pm
   PM  Quote  Reply 
4th Post
Canha
Member
 

Joined: Wednesday Mar 23rd, 2011
Location:  
Posts: 30
Status: 
Offline

  back to top

Yes, i've alredy tried this way. I can't use the other two ways because the UCM/Eth is not 6.xxx.

I've upgraded two other UCM's (UCM/KNX and UCM/GSM2) and it worked fine.


 Posted: Thursday Mar 29th, 2012 01:41 am
   PM  Quote  Reply 
5th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

What message did you get when you tried using the UCM/Ethernet to upgrade UCM/232 to a new version?


 Posted: Tuesday Apr 10th, 2012 11:09 am
   PM  Quote  Reply 
6th Post
Canha
Member
 

Joined: Wednesday Mar 23rd, 2011
Location:  
Posts: 30
Status: 
Offline

  back to top

Hi

The message that I get is shown below.

Attachment: Sem Título23.png (Downloaded 62 times)


 Posted: Tuesday Apr 10th, 2012 11:09 am
   PM  Quote  Reply 
7th Post
Canha
Member
 

Joined: Wednesday Mar 23rd, 2011
Location:  
Posts: 30
Status: 
Offline

  back to top

When I scan the modules:

Attachment: Sem Título3.png (Downloaded 63 times)


 Posted: Tuesday Apr 10th, 2012 01:09 pm
   PM  Quote  Reply 
8th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

Instructions have been sent by private message. Please check


 Posted: Tuesday Apr 10th, 2012 01:57 pm
   PM  Quote  Reply 
9th Post
Canha
Member
 

Joined: Wednesday Mar 23rd, 2011
Location:  
Posts: 30
Status: 
Offline

  back to top

Check

I'll try and then reply.

Thanks


 Current time is 09:23 am
Comfort Automation/ Security System Forums > Support > Problems & Troubleshooting > Firmware Upgrading Problems > Firmeware update
 Top

UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems