Comfort  Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register

Updating firmware UCM/ETH2 error and not comunication.
 Moderated by: ident
 New Topic   Reply   Printer Friendly 
 Rate Topic 
AuthorPost
 Posted: Thursday Feb 7th, 2013 08:56 am
   PM  Quote  Reply 
1st Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

Updating the firmware of a UCM/ETH2 gave me error. Now it is always on LEDs RDY (green), BUSY1 D2 (red), BUSY2 D3 (red) and ERR D4 (red).
On the other side, the D10 LED (green) flashes and the LED D9 (red) is never on.

The D101 LED flashes and the DS Manager detects the module but COMFIGURATOR (both 3.5.6 and 3.6.4) fails or not detect the UCM.

Sometimes I get an error telling me that the Configurator Firmware have 6 or above.

In the manual it says: "If the ID is unassigned, all LEDs are ON." but I changed the jumpers from SW7 to put another ID and unchanging.

What I can do? I have not any UCM communication but I have a UCM / KNX.

Thank you.

Attachment: IMG_0886b.jpg (Downloaded 60 times)

Last edited on Thursday Feb 7th, 2013 11:40 am by mario.jr



 Posted: Thursday Feb 7th, 2013 09:05 am
   PM  Quote  Reply 
2nd Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

Other Picture

Attachment: IMG_0885a.jpg (Downloaded 58 times)



 Posted: Thursday Feb 7th, 2013 10:21 am
   PM  Quote  Reply 
3rd Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

if you have an error in upgrading any firmware, you must not reset the module beiong upgraded or Comfort and try again the same process

The UCM firmware is now erased but you can still do the Firmware upgrade

What is the UCM ID? Do not change any jumpers at this time



 Posted: Thursday Feb 7th, 2013 11:25 am
   PM  Quote  Reply 
4th Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

The UCM ID is 1. Jumper SW7 A,B,C,D in ON (Close).

ident escribió:
The UCM firmware is now erased but you can still do the Firmware upgrade


How?

Last edited on Thursday Feb 7th, 2013 11:27 am by mario.jr



 Posted: Saturday Feb 9th, 2013 09:28 am
   PM  Quote  Reply 
5th Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

If the firmware is erased, how I can now record the firmware?

Do I need another UCM USB, RS232 or ETH?

Thanks



 Posted: Saturday Feb 9th, 2013 02:18 pm
   PM  Quote  Reply 
6th Post
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5493
Status: 
Offline

  back to top

There is a chance that you can still upgrade the firmware even if the upgrade failed and the system reset
What was the error message?
Try the upgrade again using the same method
If it iss not successful then you need another UCM to do the upgrade using the firmware ugprading cable



 Posted: Sunday Feb 10th, 2013 09:02 pm
   PM  Quote  Reply 
7th Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

Not finding the UCM.

I understand that I would be UCM / KNX, right?



 Posted: Monday Feb 11th, 2013 02:36 am
   PM  Quote  Reply 
8th Post
admin
Administrator


Joined: Saturday Mar 3rd, 2007
Location: Singapore
Posts: 1200
Status: 
Offline

  back to top

You cannot use UCM/KNX to upgrade a UCM/ETH02
You need another UCM/USB, ETH02 or RS232 to upgrade another one of these UCMs



 Posted: Monday Feb 11th, 2013 11:13 am
   PM  Quote  Reply 
9th Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

Thank you very much.



 Posted: Tuesday Feb 12th, 2013 02:58 pm
   PM  Quote  Reply 
10th Post
mario.jr
Member
 

Joined: Sunday Aug 21st, 2011
Location: Castilla-La Mancha España
Posts: 32
Status: 
Offline

  back to top

I've solved.

Got a UCM / USB with a good price and with the programming cable Update UCM / ETH.

Thank you very much for everything.



 Posted: Wednesday Feb 13th, 2013 01:10 am
   PM  Quote  Reply 
11th Post
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5493
Status: 
Offline

  back to top

Thats good. Upgrade both UCMMs to the latest version 7 firmware
Then try upgrading the UCM again without the programming cable using Comfigurator 3.6.4



 Current time is 02:51 pm
Top




UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems