Posted: Wednesday Feb 20th, 2013 05:45 am |
|
1st Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Comfigurator 3.6.5 can be downloaded from http://www.cytech.biz/product_details.php?item_id=206
This fixes bugs in 3.6.4
Bugs fixed- In KT03 adding a clock element caused an exception
- Write to KT03 may not work in some situations This was a bug fixed in 3.6.4 but it may still occur but less often. "RS4x" reply is seen in I/O Monitor. it is suspected that a hidden exception caused it, now the exception wil be visible.
- In KT03 selecting all buttons on a page and Copying may cause exceptions
- Read from Comfort with the option "Auto-generate Names" caused an exception.
- When the cursor is in the Modules Tab and the UCM connections in Options > settings is changed, the screen jumped back to the Comfort Tab although the Modules Tab is still selected
- Bus Monitor had exception in some circumstances and wrong messages about illegal commands are shown
- Minimising Comfigurator during a firmware upgrade is now prevented so the Comfigurator screen is not locked out like before
- If firmware upgrade stops due to no reply from Comfort, a dialog contiinue from last address appears, but if UCM/ETH02 is used, and connection is lost, Comfigurator does not try to reconnect before continuing the upgrade
- Zwave Status messages have been expanded.
Known Issues- For Zwave Connfigurator, the last line of Zwave Mapping is not written to EEPROM with the other lines, ie the assigned Comments and Comfort Register is not written to EEPROM. The workaround is to Read from EEPROM before adding the last line mapping and comments before writing to EEPROM
- For Zwave configurator, if a zwave node (virtual Node) is mapped to Virtual Input and the virtual node is removed, without first unmapping the Virtual Input, this causes the Comfort Zone/Input to remain as Virtual Node and this cannot be changed. Workaround is to unmap the virtual Input before deleting the Zwave virtual Node
- In Bus Monitor, if the Exit Button is pressed without first pressing the Halt button, the UCM will remain in Bus Monitor mode even though the Bus Monitor software has ended, and the UCM will not work normally, until the UCM is reset
- in KT03, copying the keypad Buttons Away, Night, Day arm buttons and pasting will leave the button actions empty, ie the button actions are not copied
Last edited on Monday Mar 18th, 2013 03:03 am by ident
|
Posted: Thursday Feb 21st, 2013 11:19 am |
|
2nd Post |
Posted: Friday Feb 22nd, 2013 08:25 am |
|
3rd Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Comfigurator 3.6.5 is released
Please upgrade to it as soon as possible as it fixes some issues in Comfigurator 3.6.4 see above list
Users of Comfigurator 3.6.x can upgrade automatically if the PC is connected to the Internet using the Menu Help > Check for Updates. Also Comfigurator 3.6.x will prompt to update the software when it is run
|
Posted: Saturday Feb 23rd, 2013 08:28 am |
|
4th Post |
juwi_uk
Member
back to top
|
In 3.6.5 I've noticed that if you check for firmware updates from the Modules tab then the "Latest Version" does not show in the attributes until you Tab away from the page and go back again.
JulianLast edited on Saturday Feb 23rd, 2013 08:28 am by juwi_uk
|
Posted: Sunday Feb 24th, 2013 01:07 am |
|
5th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
I dont see this
If I right click on a UCM and do check for updates, it says eg "current version is the latest" and shows the version and latest version
The best way to see all the latest versions is to do Scan for all modules
Then the latest version is seen for all
|
Posted: Friday Mar 1st, 2013 06:37 am |
|
6th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
2 problems wth Zwave Configurator for Comfigurator 3.6.5 have been found- For Zwave Connfigurator, the last line of Zwave Mapping is not written to EEPROM with the other lines, ie the assigned Comments and Comfort Register is not written to EEPROM. The workaround is to Read from EEPROM before adding the last line mapping and comments before writing to EEPROM
- For Zwave configurator, if a zwave node (virtual Node) is mapped to Virtual Input and the virtual node is removed, without first unmapping the Virtual Input, this causes the Comfort Zone/Input to remain as Virtual Node and this cannot be changed. Workaround is to unmap the virtual Input before deleting the Zwave virtual Node
|
Posted: Saturday Mar 2nd, 2013 08:39 am |
|
7th Post |
Posted: Saturday Mar 2nd, 2013 08:59 am |
|
8th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
No, unless you go back to 3.5.6 but that lacks may of the new Zwave features
There should not be any problems wth 3.6.5 as long as you are aware of the problem and the workarounds
|
Posted: Monday Mar 4th, 2013 07:36 am |
|
9th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Bug found in Bus Monitor for Comfigurator 3.6.5
In Bus Monitor, if the Exit Button is pressed without first pressing the Halt button, the UCM will remain in Bus Monitor mode even though the Bus Monitor software has ended, and the UCM will not work normally, until the UCM is reset
Please HALT Bus monitor before pressing EXIT from Bus Monitor
|
|