Posted: Tuesday Apr 16th, 2013 02:57 am |
|
1st Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Firmware 7.026
Bug Fixes- If Comfort voice is corrupted is bad, v? Will report v?FFFF.... Instead of no reply. That caused KP04 not to get reply to query for Vocab version causing KP04 to repeatedly query comfort Fixed Bug from 7.009
- Fixed BUG old SEM and SCS which do not support u? Scan command will be reported as u?000000FF if no of modules is less than its own id so Comfigurator scan nodules knows that it is present
Known Bugs- Reminder Enable function does not work for Reminder Numbers 9 to 16. Reminder Enables for 9 to 16 are the same as Reminder 1 to 8. This affects Scheduled Reminders only.
- Action 8 - Reset All Outputs does not work. Bug from 7.007
- for SPC abdOPT action 74, resp bug does not return to do next action from 7.010
- Action 149,0, constant add to last value did not work from 6/2/12
Sentence upgrade after vocab upgrade fails with error 29 dtad
- reminders 9 to 16 enables are the same as reminder 1 to 8 Tiime Program enables 9 to 16 are same as Time prog 1 to 8 for OPT and SPC from 6.017
- UCM u? Scan for all KP will reply KL
- action 8 reset outputs does not work from 7.007
when UCM lost comms but not lost power (remove KAKB not 12V) and is connected again so id comms is restored, module does not report 7DH (not reset) so u? reports FFFFFF and comfigurator has status still as "not found" for the module that has recovered.
Last edited on Tuesday Dec 10th, 2013 03:23 am by ident
|
Posted: Sunday May 12th, 2013 07:24 am |
|
2nd Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Firmware 7.027
- Output command ON or OFF is ignored if the output state is unchanged
- Fixed BUG action 8 reset_outputs failed (from 7.007)
Bugs- Reminder Enable function does not work for Reminder Numbers 9 to 16. Reminder Enables for 9 to 16 are the same as Reminder 1 to 8. This affects Scheduled Reminders only.
- A Flashing output on a Slave cannot be turned off by an Output On or off command. Only Reset all outputs command can reset the output. Outputs 1 to 16 on the Main Comfort board are not affected by this bug
- Pressing buttons on SCS causes the corresponding LED (output) to flash until Comfort sends a command to switch it on or off (using Response). Due to the comparison of output states introduced in 7.027, the LED may remain in the flashing state.
Please upgrade firmware from Comfigurator 3.6.x Modules Tab right click and check for updates
Last edited on Friday Jul 26th, 2013 12:32 pm by ident
|
Posted: Thursday May 16th, 2013 10:02 pm |
|
3rd Post |
gaynorc
Member
Joined: | Sunday Dec 31st, 2006 |
Location: | Ireland |
Posts: | 130 |
Status: |
Offline
|
back to top
|
I upgraded firmware 6.020 to 7.027 today.
Subsequently after arming the system to away mode, and then disarming the system, I encountered a problem with a response which had previously been working fine.
On entry to the house while in "away mode" a zone response (the entry route) switches an output to "flash" (connected to a buzzer). When the system is disarmed, the Miscellaneous Event "Security Off Response" has a response which switches that output to "off". That worked with 6.020. With 7.027 the output remains in "flash" and is not switched off.
As a temporary work around I have included in the Miscellaneous Event "Security Off Response" response an "all outputs off", and that silences the buzzer. Obviously this is not a solution. I wonder has this something to do with the new feature "Output command ON or OFF is ignored if the output state is unchanged" when the command has previousy been "Flash"?
|
Posted: Friday May 17th, 2013 03:09 am |
|
4th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
We cannot duplicate this problem in 7.027
when an output is flashing, an on or off command will stop the flashing
Can you send the cclx file to support@cytech.biz so we can check
|
Posted: Friday May 17th, 2013 06:47 am |
|
5th Post |
gaynorc
Member
Joined: | Sunday Dec 31st, 2006 |
Location: | Ireland |
Posts: | 130 |
Status: |
Offline
|
back to top
|
File now sent as requested
|
Posted: Friday May 17th, 2013 11:55 am |
|
6th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Thanks for the file. We have confirmed there is a bug in 7.027 which prevents the Flashing output on the Slave from being turned off except by All Outputs off.
Flashing outputs on Comfort outputs 1 to 16 behave correctly so perhaps you can use one of these outputs as workaround
A new version will fix that bug
|
Posted: Monday May 20th, 2013 04:19 am |
|
7th Post |
Posted: Tuesday Jul 16th, 2013 11:28 am |
|
8th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Firmware 7.028 Bug- Pressing buttons on SCS causes the corresponding LED (output) to flash until Comfort sends a command to switch it on or off (using Response). Due to the comparison of output states introduced in 7.027, the LED may remain in the flashing state.
|
Posted: Monday Jul 22nd, 2013 07:44 am |
|
9th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
Firmware 7.029
This fixes the bug from 7.027 affecting SCS.
When a button is pressed on SCS causing the corresponding LED to flash, sending a command to switch off the LED will not stop the flashing LED
Please upgrade firmware using Comfigurator
|
Posted: Saturday Jul 27th, 2013 03:19 am |
|
10th Post |
ident
Administrator
Joined: | Wednesday Aug 9th, 2006 |
Location: | Singapore |
Posts: | 3493 |
Status: |
Offline
|
back to top
|
A problem with Reminder Messages bug has been discovered which affects Firmware 7.017 to 7.031
Reminder Messages 9 to 16 Enable settings do not work
Instead the Enable settings for Reminders 1 to 8 are used
eg Reminder 9 uses the Enable setting for Reminder 1, Reminder 10 uses Remiinder 2 etc
Attachment: reminders.jpg (Downloaded 29 times) Last edited on Saturday Jul 27th, 2013 03:20 am by ident
|
|