Comfort Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register
Comfort Automation/ Security System Forums > Products > KP06/KP06A/KP04A Keypads > KP06A/KP04A Firmware > KP06 v6.008

KP06 v6.008
 Moderated by: ident
 New Topic   Reply   Printer Friendly 
 Rate Topic 
AuthorPost
 Posted: Monday Apr 14th, 2014 06:10 pm
   PM  Quote  Reply 
1st Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

The new firmware KP06 v 6.008 has been released This fixes some bugs which have been found
  1. Fixed zone name corruption (eg display "kitchen Kitchen Kitchen.."caused by the following conditions; at least 1 zone name with 16 characters; a zone with name < 16 characters triggered just before the 16 character zone
  2. Up to 15 IDs allowed in the setup menu (but requires Comfort firmware changes)
  3. LED status updated upon reset. Before LEDs were off when KP06 is reset
  4. Supports serial number function. ULT 7.052 firmware is required for this (not released yet)

Last edited on Saturday Apr 19th, 2014 05:18 am by ident


 Posted: Monday Apr 14th, 2014 09:44 pm
   PM  Quote  Reply 
2nd Post
juwi_uk
Member


Joined: Friday May 25th, 2007
Location: Newbury, United Kingdom
Posts: 1255
Status: 
Offline

  back to top

I was expecting to see a serial number?

Attachment: screenshot.png (Downloaded 41 times)


 Posted: Monday Apr 14th, 2014 09:54 pm
   PM  Quote  Reply 
3rd Post
juwi_uk
Member


Joined: Friday May 25th, 2007
Location: Newbury, United Kingdom
Posts: 1255
Status: 
Offline

  back to top

Coincidence or what but why has this trashed my UCM # 1
Since upgrade the scan returned this (see attached).
If I delete the UCM and rescan it does not find ID = 1 (Comfigurator 3.8.5).
Is it a coincidence that my KP01 and UCM are both ID 1?
All I did was check for firmware update, go with the update and it scan afterwards. Ahhhhh!
Julian
 
 
 
 
 

Attachment: screenshot2.png (Downloaded 41 times)

Last edited on Monday Apr 14th, 2014 09:55 pm by juwi_uk


 Posted: Monday Apr 14th, 2014 10:10 pm
   PM  Quote  Reply 
4th Post
juwi_uk
Member


Joined: Friday May 25th, 2007
Location: Newbury, United Kingdom
Posts: 1255
Status: 
Offline

  back to top

Here's another example where my config breaks after upgrade.  Going back to 6.007 and it works OK again.

Attachment: screenshot3.png (Downloaded 41 times)

Last edited on Monday Apr 14th, 2014 10:12 pm by juwi_uk


 Posted: Tuesday Apr 15th, 2014 01:29 am
   PM  Quote  Reply 
5th Post
juwi_uk
Member


Joined: Friday May 25th, 2007
Location: Newbury, United Kingdom
Posts: 1255
Status: 
Offline

  back to top

Ingo suggested that Comfigurator 3,.8.6 might fix as there was an issue with the first scan. So I upgraded from 3.8.5 to this version.
The first time I scanned after reset it still showed as type HDL.  I manually changed the type to "General" though and did a couple of system resets and now the scans seem to work.
Weird!
Julian

Last edited on Tuesday Apr 15th, 2014 01:35 am by juwi_uk


 Posted: Tuesday Apr 15th, 2014 06:03 am
   PM  Quote  Reply 
6th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

The problem of UCM#1 being detected as HDL is due to Comfort firmware bug. It is described here http://www.comfortforums.com/forum79/3741.html


The serial number will not appear when you upgrade to 6.008 as the serial number has not been writtten to KP06 yet
New KP06s from the factory will have the serial number
However Comfort firmware 7.052 (not released yet) is required to suport the serial number in KP06

Last edited on Saturday Apr 19th, 2014 05:19 am by ident


 Posted: Tuesday Apr 15th, 2014 10:02 am
   PM  Quote  Reply 
7th Post
juwi_uk
Member


Joined: Friday May 25th, 2007
Location: Newbury, United Kingdom
Posts: 1255
Status: 
Offline

  back to top

OK understood.  I haven't done a sync though on the keypad; I just updated the firmware so presume the *1 is done automatically during the process?


 Posted: Tuesday Apr 15th, 2014 03:09 pm
   PM  Quote  Reply 
8th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

It may do a sync if it finds that the vocabulary requires it
Anyway once the new Comfort firmware is available it will not detect HDLanymore


 Posted: Saturday Apr 19th, 2014 05:20 am
   PM  Quote  Reply 
9th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

I forgot to mention LT 7.052 (not released) is required to support the KP06 serial number display for scanning


 Current time is 06:23 pm
Comfort Automation/ Security System Forums > Products > KP06/KP06A/KP04A Keypads > KP06A/KP04A Firmware > KP06 v6.008
 Top

UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems