Comfort  Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register

ULT 7.053 to 7.057 (Beta)
 Moderated by: ident
 New Topic   Reply   Printer Friendly 
 Rate Topic 
AuthorPost
 Posted: Saturday Apr 19th, 2014 08:40 am
   PM  Quote  Reply 
1st Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

Ultra 7.053 beta can be downloaded for testing from http://www.cytech.biz/comfort_ultra_firmware.html?category_id=101

The changes are
  1. Added  action 190, timer#, count low, count high for inline delay action.
  2. Do Response after Timer action - if  Response  no = FFFF hex, then do inline response with address action 190.
  3. Fixed BUG - after *1 on Keypad to load text, ucm #1 is detected as HDL
  4. KP06 min version 6.008 so KP06 can check serial no
  5. Max keypads  8 to 15 to support 15 keypads
  6. Do not report date/time change to UCM if change < 2 seconds as SNTP cin eth03 may cause many events in event log
  7. Do alarm report zone will report last zone triggered. Last zone restored is not used.This will work in zone response.

Known Issue
  1. Extra keypads 9 to 15 may be detected after a scan using Comfigurator 3.8.7 to 3.8.8. This happens if the scan is done after initialisation. The workaround is to wait about 30 seconds and  repeat the scan. Pleaese upgrade to ULT 7.057 which does not have this problem

Last edited on Thursday May 22nd, 2014 09:29 am by ident



 Posted: Saturday Apr 26th, 2014 08:38 am
   PM  Quote  Reply 
2nd Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

ULT 7.055 (beta) can be downloaded from http://www.cytech.biz/comfort_ultra_firmware.html?category_id=101

This fixes a bug that scanning of Invalid IDs (via the u? command) did not give a valid reply.

It improves scanning of old models of Keypads and Door stations which did not recognise the u? scanning command. In previous versions, if the old keypads and DP03 are not polled by Comfort due to the number of Modules not including that ID, these old models were not detected by Comfigurator scan. You had to add the keypad or door station manually and write to Comfigurator. Once the models are polled, then the Scan by Comfigurator will detect these old models
With this firmware old models of Keypads and Door stations can be detected  by scanning even if they are not polled


Known Issue
  1. Extra keypads 9 to 15 may be detected after a scan using Comfigurator 3.8.7 to 3.8.8. This happens if the scan is done after initialisation. The workaround is to wait about 30 seconds and  repeat the scan. Pleaese upgrade to ULT 7.057 which does not have this problem

Last edited on Thursday May 22nd, 2014 09:33 am by ident



 Posted: Saturday May 3rd, 2014 06:53 am
   PM  Quote  Reply 
3rd Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

ULT 7.056 Beta can be downloaded from http://www.cytech.biz/comfort_ultra_firmware.html?category_id=101
Changes are

Bugs Fixed
  1. UCM/Cbus firmware bug fixed in  Cbus6.083. UCM/ CBUS firmware must be upgraded to 6.083 or above
  2. Fixed BUG  from 7.038 zwave status polling was wrong when Zwave status is required by the comfort apps or Comfigurator control menu
  3. Fixed problem - Extra keypads 9 to 15 may be detected after a scan using Comfigurator 3.8.7 to 3.8.8.

Improvements
  1. Tamper input introduced 1 second confrmation to reduce alarms caused by fast transitions on Tamper due to wiring or external induced voltages
  2. Z? Reports 96 zones  instead of 80 zones. The limitiation of 80 zones was because ofa bug in UCM/Cbus older than 6.083

Last edited on Thursday May 22nd, 2014 05:54 am by ident



 Posted: Wednesday May 21st, 2014 10:04 am
   PM  Quote  Reply 
4th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

ULT 7.057 Beta can be tested at the above link
The changes are
  1. Low Battery Trouble will report ID as 1 for Comfort controller to keep in line with other controller troubles
  2. Improved Control menu operation for the new redesigned Comfort apps so that the status button does not change state several times due to switching on or off



 Posted: Thursday May 22nd, 2014 09:27 am
   PM  Quote  Reply 
5th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

ULT 7.057 has been released. See summary of changes in http://www.comfortforums.com/forum79/3815.html

This fixes  the problem of extra keypads 9 to 15 appearing after a scan

Please upgrade by right clicking on the Controller and selecting "Check for Updates" if you are connected to the Internet


You can also download the firmware by right clicking  and selecting "Download Firmware Upgrade" and later "Upgrade Firmware from Local File"


Last edited on Thursday May 22nd, 2014 09:50 am by ident



 Current time is 01:08 pm
Top




UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems