Posted: Sunday Aug 27th, 2017 10:21 am |
|
1st Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO Firmware 7.008
Bugs Fixed- Fixed Dimmer to report counter.
- Fixed bug -Blinds AC function's down relay fails to switch off. This is if feedback counter is assigned and it affects submodule 2 only.
- Fixed wrong input number reported, when Register Type is set to “Input†for “Digital Inputâ€
New Features- For Blinds AC function, extend “ignore current sensing†duration from 250ms to 1000ms. This is to compensate for hardware slow detection of low current motors.
- For Blinds AC function, LED is added to indicate current detection status. The LED is turned on if current is detected.
- Support new “Calibration offset†parameter of Temperature Sensor input function.
- Input function Support of new “Virtual Input†register type, for various input functions.
- Supports new ISM08 submodule functions.
New Features require Comfigurator 3.11.14 and above
Last edited on Saturday Nov 4th, 2017 11:52 am by slychiu
|
Posted: Saturday Nov 4th, 2017 11:40 am |
|
2nd Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO 7.009
- Improved IR Signal input function. Invalid counter values (ie. >63) are mapped to value 1 instead of ignoring it. Useful in situations where signal 1 is ON signal.
|
Posted: Sunday Oct 7th, 2018 06:58 am |
|
3rd Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO Firmware 7.010
Supported new “Virtual Input†register type, for “Digital Input†input function.
Note that Comfigurator version 3.12.7 minimum is required
Last edited on Sunday Oct 7th, 2018 07:00 am by slychiu
|
Posted: Wednesday Dec 11th, 2019 12:24 pm |
|
4th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO Firmware 7.014- Dimmer 0-10V Function, supports new Direction and Quick Press parameters. This allows different ways for the switch to control the dimmer output eg alternate pressto change direction, or only 1 direction up or down, for quick press and long press
- Analog Output 0-10v function supports register flag assignment.
- Analog Input (0-10v) function supports sensor value reporting, as long as sensor number is assigned (even if a Flag or Virtual Inputs is not assigned)
Last edited on Tuesday Jan 16th, 2024 07:18 am by slychiu
|
Posted: Sunday May 8th, 2022 07:17 am |
|
5th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO 7.017
Proportional + Integral ( PI) control function in analog outputs. - Output move direction is based on Summer/Winter flag status.
- When PI flag is off, analog output can be controlled via counter.
- Supported ramping for PI output.
- Bumpless transfer, with CO-bias feature,
- When PI flag goes off, output remains unchanged.
- Improved register reporting.
Take note that if PI function is used, IR transmission function will be disabled,
IRIO 7.018
Changes for PI control function: - Fixed calculation error on the integral part where it is not smooth.
- Previously in some cases, the change was every 10 seconds.
- Changed integral sum from automatic start, instead of taking the latest set samples.
- Double gain limit to 32.
- Added new “Sample time†parameter.
- Added new “Direction†parameter.
- Set checks for integral sum overflows.
IRIO 7.019
- Supports 4 dimmers (analog outputs) for IRIO02.
- Support ID detection for new ISM09,
- Note that ISM09 (for PT100)will be identified wrongly for older firmware
Last edited on Sunday May 8th, 2022 07:19 am by slychiu
|
Posted: Friday May 12th, 2023 03:06 am |
|
6th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO 7.024
BUGS- For IRIO/IO, Outputs mapped to Flag does NOT work. That means that if the mapped Flag set/clear does not affect the Outputs as expected. DO NOT Upgrade for IRIO-IO
Improvements and changes
Improvements in Proportional and Integral (P+I) Function for Analog Outputs, and fixed Bugs. Each IRIO and 2 Analog Outouts on the base board which provide 0 to 10V to control valves etc. These can work as independent P+I control. see the IRIO manual at http://www.cytech.biz/irio_module.html
This can be used for Air Handling Unit (AHU) control
Last edited on Tuesday Jan 16th, 2024 07:17 am by slychiu
|
Posted: Tuesday Jan 16th, 2024 07:16 am |
|
7th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO Firmware 7.026 (18 Dec 2023)
Bugs- For IRIO/IO, Outputs mapped to Flag does NOT work. That means that if the mapped Flag set/clear does not affect the Outputs as expected. DO NOT Upgrade for IRIO-IO
Changes and Improvements
Temperature Sensor Function in IRIO:- This function is tuned to use with new sensor MF52D103F33950 instead of the beaded NTC temperature sensor with short leads . This sensor comes with a 10 meter waterproof insulation shield which is more suitable for industrial monitoring.
- The temperature range has been widened to -30 to 100 degree Celsius (previously min 0 to 100 deg C). Return value of 101 if exceed upper limit (ie. 100). Return value of -31 if exceed lower limit (ie. -30) or sensor is not connected.
Last edited on Friday Jan 26th, 2024 08:13 am by slychiu
|
Posted: Wednesday Jan 24th, 2024 06:26 am |
|
8th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5650 |
Status: |
Offline
|
back to top
|
IRIO Firmware 7.027
Bugs fixed- IRIO-IO (ISM08) outputs mapped to flag did not work - from IRIO 7.020
Last edited on Wednesday Jan 24th, 2024 06:27 am by slychiu
|
|