Posted: Friday Dec 11th, 2020 03:36 am |
|
1st Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.183
Known Bugs- Action 1 (Announce Zone Name) in Zone Off Response will skip announcing the 1st word in the zone
Bugs Fixed - Fixed BUG for eth03 plug in to CM9001 - UL with 2 bytes always returns the 2 same bytes
- Event Log fixed BUG last event 27 was 68 may cause event log to crash from 28/6/18
- Fix BUG for partitions arm to away sometimes dis not work
- Fix bug from 13/6/19 Security check may use wrong partition
- Fix bug from 6/3/20 if log in wrong code using ext232 there is no reply LU00, comfigurator waits and times out
- Fix Bug Monitor Mode MO00 cannot exit from monitor mode
- Fixed bug Monitor Mode MO00 cannot exit from monitor mode
- Fixed Bug Action 158 clear and set counter did not work, but toggle worked
- Fixed BUG dR report was not sent when ETH03/Wifi01 was plug in on CM9001
- Event Log fixed BUG last event number was wrong, may cause event log to crash from 28/6/18
Event Log- Change in Event Log indexing. Reduces Wear on the EEPROM due to writing the event log pointer with every event. Also reduces time to erase the whole event log Fixed other bugs
- Event Log fixed BUG last event number was wrong, may cause event log to crash from 28/6/18
- Event Log will not announce month 0 if it is encountered
Action Codes- Action 162 Assign Reminder to Alarm to assign a recorded reminder message to an Alarm to replace sentence. If no the assigned Reminder number is recorded, the alarm message will be played
- Action 163 assign reminder no to zone. if zone has reminder message, it will play the reminder message in event log, zone announcement and security check, but zone menu will continue to play the zone words. If the Reminder is assigned to a zone, but the reminder message is not recorded, the zone words are played
- Added Action get parameter 61 Login Partition
Partitions/Areas- Partitions If all keypads are in partition 0, allow parttions to be enabled. some systems disarm by switch
- Announce Area/Partition number in user menu if partitions exist
- For partitioned system, arm and disarm security will announce Area (Partition) Number after announcing security mode. Requires Vocab version 42
Announcements- Dial out announcements - changed order for dial out alarm announcements. 1st play recorded alarm message, then alarm type, then alarm pararameter announcement
- Vocabulary version 42 sentence 87 is Area (N)
- Detector_announcement - if not trouble or restore, announce reminder call detector_name so reminder can be announced detector_announce if restore zone but no words in zone, call say_zoneNrestore. require vocab v43
- Voice menu add 8 for zone announce Require vocab 43
- zone restore announcement - zone name restore instead of just Restore without zone
Environmental Monotoring System CM9001-EMS- EMS enable reminders for zones and alarms. disable Scheduled Remimders for EMS for play reminder action only
- Enabled 16 Reminders for ems
- Allow Ems without Incoming recorded messages, with Reminders in Responses
- EMS Voice menu add 5 for reminder messages f
- EMS sensors fix bug sensor - setpoint comparison was unsigned, ie negative values are taken as positive. process_sensortab fix bug counter compare with max and min setpoints was unsiged should be signed.
- EMS sensors.mac process_sensortab limit counter setpoint to -128 to 127. fix bug counter >255 was set to 255 ie -1
- EMS Sensor Setpoint Counter prevent max/min setpoint check from doing endless loop
- EMS sensors - adjust_sensor limit final sensor values to -128 to + 127 after adjustment, but allow signed 16 bits intermediate. Aallowed sensor values for scaling (;1 = 0 to 99. sensor 0 to 255, 2 = multiply by scale factor. sensor -128 to + 127, 3 = divide by scale factor, sensor -32768 to 32767. allow larger range for division. final value will be -128 to + 127
Misc- Motion sensor Timer enabled for EMS. query d? got reply NA before
- For wifi NTP, update time daily at 12: 05 am instead of 4 AM
Last edited on Saturday May 7th, 2022 09:45 am by slychiu
|
Posted: Sunday Dec 13th, 2020 05:01 am |
|
2nd Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Bug in 7.183
Action 1 (Announce Zone Name) in Zone Off Response will skip announcing the 1st word in the zone
|
Posted: Monday Jan 4th, 2021 04:19 am |
|
3rd Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.185 (Beta)- Fix bug from 25/5/20 zone restore action 1 when zone restored, 1st word in zone is skipped,
- Fixed Bug In partitioned system, siren sounds for arming wer not heard on the partition keypad
- Fixed Old bug - if there is zone trouble in a partitioned system at reset, the partition keypad will show "Communications Failure" without ID (instead of zone trouble)- Fixed Old Bug - if zone trouble is force armed when armed, after disarmed, the zone trouble is not shown until armed again or security check
- Fixed Bug for Wifi Plug in, if if not logged in or does not log out, idle timer from EEPROM expires does not reset Wifi module. so if wifi lost connection, the module is not reset
- Fixed Old Bug Igf there s zone trouble and security is force armed, after disarming, the zone trouble is not shown anymore untill system is armed or security check
- Fixed old bug in Partitioned system after alarm sren times out, the alarm state does not go to alert state. This caused after arm fail, not able to arm
- Fixed old bug SMS disarm could not disarm from arm fail
Bugs- For Partitioned systme, when user logs in for partition >0, every minute the partition may be changed to to 0 so the user may arm or disarm to partition 0
Please download the beta firmware from http://www.cytech.biz/comfort_ultra_firmware.html
Last edited on Saturday Mar 13th, 2021 08:04 am by slychiu
|
Posted: Saturday Mar 13th, 2021 08:02 am |
|
4th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.187
Bugs Fixed
- Fixed Bug in CM9001 Main Board for virtual Input 1 to 8 did not waork correctly
- Fixed bug for partitions – when user in partition > 0 signs in sometimes the partition getrs set to 0 at the start of each minute (by vacation mode check)
|
Posted: Saturday Dec 11th, 2021 01:19 am |
|
5th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.192
Known Issues- Digital Zone type on CM9001/SEM . If zone is Digital Normally open, Off zone is reported as ON. also for non digital zone, trouble Short Circuit reports as Open circuit. This is an old bug affecting previous firmware
- Keypad to Door Station Intercom does not work. KP cannot hear DP
Bugs Fixed
- Fixed Bug If firmware upgrade failed and power off and, firmware upgrade from UCM ID1 did not work
- Fixed bug ultra cannot upgrade to EX by ETH03 plug in
- FIXED BUG . UCM/LOG and KNX/LOG did not work for RIO
- Fixed BUG eth03 plug in did not report RIO Input state change
- Fixed BUG vacation mode for partition system did not set partition correctly
- Fixed BUG If no zones in partition 0, cannot arm partition 0 without zones. exit time does not end
- Fixed BUG for ETH03 plug in ST command reply did not work
New Features and Changes- When Sign in on Phone : check if user who log in is enabled for higher partitions, and say "select Area". check if user is enabled for higher partition, and if so log in to the higher Area/partition.
- For Arm security system, if area/partition has no zones arm/disarm is not enabled.
- Keypad to Door Station Intercom. Keypad Press and hold button is one way KP to DP. If KP button is released then KP to DP is full duplex
- If IDBUTTON on CM9001 is pressed and held at reset, disable Responses This allows system to work even when there are responses with endless loop, ie Responses calling themselves, or problems in the Startup Response.
- Added Test mode commands to support production tester functions
Last edited on Wednesday Dec 29th, 2021 12:37 am by slychiu
|
Posted: Saturday Dec 11th, 2021 01:46 am |
|
6th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.193 (Beta)- Fixed old BUG- Digital Zone type on CM9001/SEM . If zone is Digital Normally open, Off zone is reported as ON. also for non digital zone, trouble Short Circuit reports as Open circuit. This is an old bug affecting previous firmware
- For CM9001-EMS Event Log Sensors with value = 0 do not report in the event log every hour to avoid filling up the event log
Known Bugs- For Keypad to Door Station Intercom, Keypad cannot hear the Dooor station
Last edited on Friday Dec 17th, 2021 12:21 am by slychiu
|
Posted: Saturday Dec 11th, 2021 08:05 am |
|
7th Post |
Ian
Member
Joined: | Saturday Aug 19th, 2006 |
Location: | United Kingdom |
Posts: | 249 |
Status: |
Offline
|
back to top
|
I am currently on firmware 7.183 on II Ultra.
Comfigurator version 3.13.7.0.
Comfigurator tells me there is a firmware update to 7.192. When I say yes to upgrade nothing happens.
Any idea why that might be?
(I know I can do it manually but would prefer to do it automatically)
|
Posted: Sunday Dec 12th, 2021 03:49 pm |
|
8th Post |
Posted: Friday Dec 17th, 2021 12:20 am |
|
9th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
A Bug has been discovered with ULT 7.192 and 7.193 when using the Keypad to Door Station intercom. The Door station cannot be heard in the Keypad. A firmware upgrade will be released soon to fix it
Last edited on Friday Dec 17th, 2021 02:04 am by slychiu
|
Posted: Friday Dec 17th, 2021 02:58 am |
|
10th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.194
Bugs Fixed- Fixed Bug from 7.192 - Keypad to Door station Intercom was 1 way only. KP could not hear DP
Those who use the Door station, please upgrade the firmware
BUG in OPT 7.194
OPT 7.194 may have reset problem - cannot start up
Last edited on Friday May 13th, 2022 05:57 am by slychiu
|
Posted: Saturday May 7th, 2022 09:57 am |
|
11th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.196- Occupancy Action 27 for zone will report dR01 only if occupancy timer has stopped to prevent dR01 report when movement is detected
|
Posted: Sunday Dec 18th, 2022 01:18 am |
|
12th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Version 7.200
Bugs Fixed
- Fixed BUG wifi detection was wrong if no module plugged in on 10 way connector. Controller may keep resetting if there is no plug in. As a result Initialisation may take up to 3 seconds after power on if ETH03 is plugged in.
- LED03 RED ON when wifi detected. LED3 red led will go off if wifi submodule is not detected
- Fixed BUG for LGX01, UCM/Logic, KNX/Logic - if eeprom file system is incorrect, Controller does not poll ucms so it was not possible to write to Comfort
- Fixed BUG in comfort protocol messages CTNNvv was seen as NNvv without CT
New Features and Changes- d? query will reply d?00 if Motion Timer is disabled ( NOT NA) -0 works for ETH03 plug in not UCM which needs firmware upgrade
- Power failure alarm increased delay from 10 secs to 60 seconds due to some systems having power failuyre alarms suspectshort drop in power caused the problem. sent to Robert astrol to test
Improved Saving Flags in eeprom for EMS and LGX
|
Posted: Tuesday Jan 3rd, 2023 12:18 pm |
|
13th Post |
Majik
UCM Pi Users
Joined: | Saturday Aug 26th, 2006 |
Location: | |
Posts: | 33 |
Status: |
Offline
|
back to top
|
I'm having major issues doing a cable firmware update. I have a relatively new Comfort II Ultra system which, unfortunately, failed a firmware update and stopped working.
So I have attempted to do a serial cable update as described in http://www.comfortforums.com/forum4/1216.html
I dug out my trusty old UCM serial unit which I have previously used for firmware updates. When I plugged it in as described, the UCM started up fine when the RS485 cable was connected, but as soon as the PROG connector is inserted, the UCM seems to go into a restart loop. I tried another UCM and it does the same thing, so it seems to be the controller, not the UCM.
Note that my controller does not seem to have a PP2 header.
Am I doing something wrong, or is the firmware bricked?
Cheers,
KeithLast edited on Sunday May 7th, 2023 03:05 am by
|
Posted: Tuesday Jan 3rd, 2023 01:05 pm |
|
14th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
The ucm with programming cable should be able to upgrade the firmware. Make sure the cable with 4 way and 2 way connectors are on the ucm and the 6 way connector is connected to pp1 on the comfort. They're is no pp2 on the new comfort pcb. In your photo you do not show the connections to the programming cable
|
Posted: Tuesday Jan 3rd, 2023 02:47 pm |
|
15th Post |
Majik
UCM Pi Users
Joined: | Saturday Aug 26th, 2006 |
Location: | |
Posts: | 33 |
Status: |
Offline
|
back to top
|
I did have the cable connected to the connectors as described.
As I said, when I connected the RS485 bus, the UCM powered up as expected. As soon as.I connected the 6 way cable, it started power cycling.
As it is, I'm actually now at the airport traveling (to Singapore) for an extended period so I can't do anything about it now anyway.
I will have to sort it out when I come back to the UK.
By the sound of it, the board may have gone faulty.
Cheers,
Keith Last edited on Thursday Jan 5th, 2023 02:08 am by Majik
|
Posted: Saturday May 6th, 2023 11:35 am |
|
16th Post |
Majik
UCM Pi Users
Joined: | Saturday Aug 26th, 2006 |
Location: | |
Posts: | 33 |
Status: |
Offline
|
back to top
|
An update on this as I'm currently home in the UK. This still doesn't work using a new UCM/USB board to try to program the firmware.
Just as with the previous UCM I tried, when you plug the programming cable in, it goes into a continuous reset loop:
https://photos.app.goo.gl/Je4xq96KPceWUyQi9
It looks like I may need to replace the main board.
Cheers,
Keith
|
Posted: Sunday May 7th, 2023 03:06 am |
|
17th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
I suggest you send the Comfort PCB and ucm to Laser and get them to check if the upgrade can work, and verify which parts may need replacing
|
Posted: Friday May 19th, 2023 10:10 am |
|
18th Post |
Majik
UCM Pi Users
Joined: | Saturday Aug 26th, 2006 |
Location: | |
Posts: | 33 |
Status: |
Offline
|
back to top
|
Unfortunately, I didn't have much time to look at this before I had to travel.
I had already ordered a replacement board from Laser, as well as the UCM/USB.
I ended up replacing the CPU board and leaving the DSP board, simply for speed and convenience, and reloading the config across the network, so it is back and running.
However, I did initially try programming the new CPU board from the UCM/USB using the programming cable, and that failed in the same way, with the continuous reboot.
So this indicates some other issue with the system which I haven't tracked down: I suspect either the DSP board or, maybe, a power problem (although I have the new enclosure with 2A supply, and I'm not running that many things on it).
Either way, it currently works.
I was planning to bring the original CPU board back to Singapore with me but, in my rush, I forgot to pack it.
Cheers,
Keith
|
Posted: Saturday May 20th, 2023 12:47 pm |
|
19th Post |
Majik
UCM Pi Users
Joined: | Saturday Aug 26th, 2006 |
Location: | |
Posts: | 33 |
Status: |
Offline
|
back to top
|
When I go back to the UK later in the year I'll do a few more tests and, if I don't find a solution, I'll try to remember to pack the board when I come back to SG.
Cheers,
Keith
|
Posted: Friday Feb 23rd, 2024 08:28 am |
|
20th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5596 |
Status: |
Offline
|
back to top
|
Firmware 7.202
No functional difference from 7.200. The only change is to accomodate production test
|
|