Bug on KP04 (All versions) 9 Sept 2009 - This has been found to occur on a few KP04s. When a Phone Trouble Alarm occurs the ...   Thursday Sep 10th, 2009 04:35 am

When you say the LEDs are flashing do you mean D9 and D10 which means it is communicating? Could the ID of the UCM be ...   Thursday Sep 10th, 2009 01:24 am

I can just click on the link on the website http://www.cytech.biz/Downloads/Files/192/voiceproc.pdf and open in Acrobat Does anyone else ahve the same problem? ...   Thursday Sep 10th, 2009 01:13 am

Can you give an example of how the password is sent by hexadecimal DFor example if the code is "1234" what is sent by Vantage? ...   Wednesday Sep 9th, 2009 12:05 pm

Are you sure the responses did not run? Can you use the Comfort Bus Monitor (in Tools of Comfigurator 3), enter yiur user code and press ...   Wednesday Sep 9th, 2009 11:41 am

If D9 (red) is not blinking it means that the UCM/Smartfit is noit responding to polls from Comfort. D10 (green) blinking means it is receiving ...   Tuesday Sep 8th, 2009 07:20 am

Please note the following bugs found in Comfigurator 3.1.1 The Dynalite Preset code is reduced by 1 when a ccl file created by Comfigurator 2 is ...   Monday Sep 7th, 2009 12:31 pm

We have seen limited numbers of the Merten Connect switches as they have not introduced them everywhere yet. We have tested adding these switches to ...   Wednesday Sep 2nd, 2009 10:50 am

As a security system, Comfort deliberately forces you to acknowledge that there was a power failure. It may be important that there was not a power ...   Wednesday Sep 2nd, 2009 08:59 am

I am not sure what you intend to do. The ZDW232 is a Z-Wave wall switch which replaces a conventional switch The Merten Connect insert presumably ...   Wednesday Sep 2nd, 2009 01:23 am

We advise in the manual to close all ports except the one used for SSL, but as long as your system is on the internet, ...   Tuesday Sep 1st, 2009 11:36 am

Cytech's new Prontoscript Module (used for Pronto 9400, 9600, 9800) is able to control KNX devices when connected to the UCM/KNX. Whats more, any change ...   Tuesday Sep 1st, 2009 09:30 am

The problem with READ fdrom EEPROM sometimes coming up with blank data has been fixed in Comfigurator 3.1.1 ...   Tuesday Sep 1st, 2009 09:25 am

OK, we will leave that as an unsolved mystery then:) ...   Tuesday Sep 1st, 2009 09:22 am

Can you be more specific? The TWS rating is 230V 6 A rms as specified in the TWS Manual Please download the TWS Manual from the ...   Tuesday Sep 1st, 2009 09:03 am

Thats bizzare. It should not matter how you connect to Comfort, I have just tested getting system information  on our dollhouse CWM in passthrough port ...   Tuesday Sep 1st, 2009 08:57 am

Comfort can send any command to the UCM Rs232 port using the Send RS232 action in Response wizard If the Vantage product (owned by Legrand)  can ...   Tuesday Sep 1st, 2009 01:12 am

You can access Engineer Menu remotely and erase the event log. However F0 on the keypad must be pressed to enable engineer menu as a protection ...   Monday Aug 31st, 2009 01:06 am

This is a good opportunity for a tutorial on C-Bus interfacing to Comfort See your Garage Sensor on Zone 1 ("Standard Passive"), whose Response is If Flag ...   Tuesday Aug 18th, 2009 10:00 am

The link is incorrect and will be corrected in the next few days. There is a problem with our servers currently This topic shall be closed ...   Sunday Aug 16th, 2009 03:55 am

The new UCM/KNX allows for any KNX Physical address to be selected in the  KNX Properties page instead of having to depend on shunts. This ...   Sunday Aug 16th, 2009 03:42 am

Check that the D9 and D10 LEDs on the UCM/CBUS are blinking, as this shows that it is communicatiing with Comfort. The ID on SW7 ...   Sunday Aug 16th, 2009 02:08 am

Changing the group address of a button is not possible, and that has been confirmed by Clipsal. The functionality that you mention is disabling the ...   Saturday Aug 15th, 2009 08:02 am

We are looking at the possible function of relabelling DLT switches from Comfort, and would like some feedback on how it would be useful. I ...   Saturday Aug 15th, 2009 07:16 am

Thats good. There were some minor bugs with 5.192 including the Read from Group Aggress that you reported. This has been fixed so you should ...   Friday Aug 14th, 2009 09:39 am

The UCM/KNX is now officially released, please visit the download links highlighted below Firmware version minimum = KNX 5.195 UCM05 Firmware minimum = UCM 5.192 Comfort Firmware minimum ...   Friday Aug 14th, 2009 09:24 am

Comfigurator 3.1.1 is now available, please see http://www.comfortforums.com/forum20/1570.html ...   Friday Aug 14th, 2009 09:03 am

Comfigurator 3.1.1 is now available for download from here This version fixes some issues with UCM/KNX support, and so is the version that must be used ...   Friday Aug 14th, 2009 09:03 am

The lesson here is not to use 2 i's in a domain name, I guess ...   Friday Aug 14th, 2009 06:53 am

Please get a replacement from your supplier. We will look at the cause of the problem when we get it back from them ...   Friday Aug 14th, 2009 12:43 am

I have sent you the contact of a Portugal dealer You usually use Comfigurator to program Comfort Responses or "macros" Programming by keypad is also possible but ...   Friday Aug 14th, 2009 12:39 am

I have not seen this symptom before Could it be a problem withyour PCI card causing a conflict with the Rs232 port? Can you try removing the ...   Thursday Aug 13th, 2009 01:43 pm

We will take a look at the possibility since you asked nicely:) No promises though as some things are easier asked than done ...   Thursday Aug 13th, 2009 12:31 pm

There is not a way to prevent dial out for restore AC Failure when you have enabled the dialout for AC Failure itself Most people would ...   Thursday Aug 13th, 2009 07:13 am

strange, if you type www.quiiq.com it goes to the correct website ...   Thursday Aug 13th, 2009 12:58 am

You must have 1 keypad in the house even if it is inside a room. You cannot depend on touchscreens They look nice but if ...   Wednesday Aug 12th, 2009 12:41 pm

You can use two touchscreens connected to UCMs, as up to 8 ucms can be connected to a system We are devloping the new version of ...   Wednesday Aug 12th, 2009 12:33 pm

Keypads 150 m away should be ok. If you can, use shielded CAT5 to minimise noise on the audio. Double up the 12V and Ground ...   Wednesday Aug 12th, 2009 11:47 am

A new version of the Comfort Prontoscript module is available from the link in the original post This requires ProntoEdit Professional 2.3.17 and above which can ...   Wednesday Aug 12th, 2009 02:10 am

Does this happen every time after you write to the EEPROM? ...   Tuesday Jul 28th, 2009 01:49 am