Are you talking about 7.213? ...   Saturday Feb 24th, 2024 05:38 pm

This is ucmPi. The trace which I shared above does not show the IPs. ...   Saturday Feb 24th, 2024 09:38 am

Seeing that there is a version 7.202 which is the next version from 7.200, not sure why I am seeing 7.201 as current and latest ...   Friday Feb 23rd, 2024 02:38 pm

When I run a trace on the UCM, I see a lot of these  netserver:Fri Feb 23 2024 16:05:18 GMT+0200 (South Africa Standard Time):1:Cannot ping, not ...   Friday Feb 23rd, 2024 01:16 pm

Sorted it out with Fing. ...   Tuesday Feb 20th, 2024 10:11 pm

I lost my router, so am rebuilding my network. Got everything by the ucmPi working, I tried getting my IP using SW4 (REQ) and  https://uhai.alphawerk.co.uk/finder.html, but ...   Monday Feb 19th, 2024 09:37 pm

So how we remotely reset the system if we are not at home when this occurs? ...   Tuesday Jan 9th, 2024 05:42 am

Early morning we had serious thunder and lightning, the alarm went off (tamper, communication loss), could not use the keypad to disarm, eventually had to ...   Monday Jan 8th, 2024 09:05 pm

It looks like it was a dodgy sensor, replaced it yesterday, and have not had the issue since. ...   Sunday May 14th, 2023 11:09 am

How would I know which CM9001 it is? The zone trouble only started reporting two days ago. The door open/close is still being reported accurately. The zone ...   Tuesday May 9th, 2023 01:13 pm

I have a input zone (6) that has a magnetic contact and has never given issues for years until two days ago when it ...   Tuesday May 9th, 2023 09:59 am

I have a replacement laptop that has the same OS Build as my old laptop (19043.1165), but on the replacement laptop I get an error ...   Tuesday Nov 9th, 2021 06:05 am

The reset fixed the issue. ...   Thursday Jun 17th, 2021 09:19 pm

We had a prolonged power failure where the backup batteries ran dry.  I noted that comfort time was wrong once the power was wrong, so ...   Thursday Jun 3rd, 2021 03:54 pm

Can I use Beyond DT Wireless Outdoor Detector with Camera  with Comfort, maybe using  Nova 4? ...   Monday Aug 3rd, 2020 05:53 pm

Email sent. ...   Monday Mar 9th, 2020 10:43 am

I have searched the Comfigurator project for Cbus2 CbusUCM 56 5 and Cbus2 CbusUCM 56 47, could not find any. I have checked the Day Mode ...   Monday Mar 9th, 2020 08:14 am

Am having a similar issue again, this time, every time the alarm status changes. So when the alarm status changes to Day Mode, the following are ...   Sunday Mar 8th, 2020 09:48 pm

I was travelling so did not get a chance to physically change the IDs. So this past weekend before attempting to do the change, I ...   Tuesday Mar 3rd, 2020 05:03 pm

 ID#2 is displayed, which is the correct ID, (ID#1 and ID#3 are the other 2 keypads). There is no communications failure alarm.  It seems day and night  ...   Wednesday Feb 19th, 2020 10:23 am

There is no sound coming from the keypad. ...   Tuesday Feb 18th, 2020 01:17 pm

The screen is consistently showing the ID# and version. Nothing else shows on the screen. I can however see the keypad from Comfigurator and I have ...   Tuesday Feb 18th, 2020 11:28 am

One of my two KP04 (version 1.017) stopped responding to keystrokes about 4 days ago. It constantly shows the ID# and Version on screen. I have Comfort ...   Monday Feb 17th, 2020 05:06 pm

I followed the advice to ask Fermax technical sales, did not get anywhere. When a technical sales person tells you how much they hate automation and ...   Tuesday Sep 17th, 2019 08:54 am

I could not get Comfigurator to connect to the UCM, even though Comfort ServerManager detected the UCM. So I disconnected the UCM for a few seconds ...   Tuesday Sep 10th, 2019 10:46 am

I have Cbus GA 39 (Kitchen Light 1) mapped to Counter 39 and        Cbus GA 40 (Kitchen Light 2) mapped to Counter 40.      ...   Tuesday Sep 10th, 2019 06:01 am

Find attached the bus Monitor. ...   Monday Sep 9th, 2019 07:46 pm

This is what the monitor shows < CT273F00 < CT284900 < CT279900 < CT28A500 < CT274000 < CT284A00 ...   Sunday Sep 8th, 2019 02:13 pm

Done, cclx file sent support@cytech.biz. ...   Sunday Sep 8th, 2019 07:11 am

I am using Comfigurator with Comfort 2Z Ultra (v 7.160), Cbus2 Ucm (v7.106)   DateTime= 2019/09/07 20:56:35.245   App= 202  Trigger Control      Group= 014  Kitchen    ...   Saturday Sep 7th, 2019 07:50 pm

Ingo wrote: I tend to agree with Chiu. When a zone is initially unsealed and you bypass it, no new zone changes are sent. If, ...   Monday Oct 29th, 2018 01:17 pm

When I bypass a zone in Comfort, the event is logged in C-Bus Toolkit (Security zone isolated). I expected to see an event to indicate ...   Monday Oct 29th, 2018 08:00 am

slychiu wrote: Counters can be mapped to Zwave, Cbus, KNX and many other systems, not just to counters in isolation from other systems What I was suggesting ...   Sunday Nov 23rd, 2014 01:18 pm

slychiu wrote: For zwave this means that 50% ie value of 50 would be converted to 50/255 = 18% instead of 50% The Zwave concept is ...   Sunday Nov 23rd, 2014 11:17 am

slychiu wrote:  There are some systems like Zwave where the counter values are 0 to 99 for dimming levels and 255 for on Expressing the values ...   Sunday Nov 23rd, 2014 10:00 am

CytechMartin wrote: No, 255 means 100%, 0 means 0% I know that. It might make more sense for end users, especially for dimming and the likes. Just ...   Saturday Nov 22nd, 2014 04:45 pm

slychiu wrote: The slider on the Control menu mapped to Counter feedback is now working. The position of the slider sends the value 0 to ...   Saturday Nov 22nd, 2014 12:18 pm

slychiu wrote: DSP Voice Reset occurs when the voltage to the DSP falls to a low level and the voice is disabled to prevent ...   Monday Oct 27th, 2014 07:50 am

Ingo wrote: Running the garage door motor from the Comfort 12V supply? No, the garage door has it's own 24 volt battery. ...   Sunday Oct 26th, 2014 11:30 pm

I had two cases where when opening the garage door, the control panel did a soft reset. The first occurrence the alarm was in day ...   Saturday Oct 25th, 2014 11:47 pm