Troubles > Comfort 1 System 12v Fail (3 replies - 6892 views)
Many thanks for advice, I have disconnected the plug with S12v, com, 12v. Then checked voltage on S12v and12v. The voltage remains at less than ... Thursday Sep 1st, 2011 04:52 pm Troubles > Comfort 1 System 12v Fail (3 replies - 6892 views)
I know it's old, but my trusty Comfort 1 (Action 4.233) has seemingly got big trouble....I would appreciate some pointers in fault finding...
Today the system ... Wednesday Aug 31st, 2011 10:32 pm Comfort I Issues > Comfort 1 PC01-001 rev E mainboard (5 replies - 14180 views)
Many thanks...
Took your advice and reviewed the panel and connections... there is only 2 pins
marked TR and COM
What threw me was beside the third ... Thursday Jan 29th, 2009 08:54 pm Comfort I Issues > Comfort 1 PC01-001 rev E mainboard (5 replies - 14180 views)
Can you clarify the following for me please.
The J4 (tamper)on my board from left to right is
GRND - TR - COM
on the rev E pcb ... Monday Jan 26th, 2009 08:46 pm Problems & Troubleshooting > Cequera Bell Box (15 replies - 24712 views)
My apologies...as I said I am mechanical based....
It was with respect to tamper.... I appreciate the voltage will be in parallel. I'll connect up the ... Tuesday Oct 28th, 2008 10:20 pm Problems & Troubleshooting > Cequera Bell Box (15 replies - 24712 views)
JUst trying to pick up on Cequra bellboxes.....I have one fitted (a long time ago, over 8 years), and purchased a new one to have ... Tuesday Oct 28th, 2008 12:18 am Miscellaneous Interfaces > Comfort and Visonic (8 replies - 18953 views)
Very many thanks...I did suspsect, but being a mechanical engineer thought I better ask the guru.
thanks again
Campbell:D
... Monday Oct 20th, 2008 04:44 pm Miscellaneous Interfaces > Comfort and Visonic (8 replies - 18953 views)
Many thanks, I understand the in series resistor, but confess ignorance in how and where to connect the parallel 4k7 resistor.
After this I 'll ... Monday Oct 20th, 2008 09:49 am Miscellaneous Interfaces > Comfort and Visonic (8 replies - 18953 views)
Chiu,
I am hoping you can advise on best wiring for MCR 308 to Comfort..
Loooking at wiring in section 4.3 (figure 6) of Visonic manual
http://www.cmacd.org/comfort/MCR308_English_Installation_Instructions.pdf
and section ... Sunday Oct 19th, 2008 11:12 pm Questions on Using Comfort > Upgrading comfort 1 Pro to Ultra (7 replies - 11340 views)
Chiu, Can you point me in direction of worfdlist to check against the one I have for UK
http://www.comfort.org.uk/technical/comfigurator/voice/ukvoc267-15.bin
wordlist - http://www.home-control.co.uk/technical/comfigurator/Pro_Ultra1_UK_Residential_Wordlist.pdf
many thanks
Campbell
... Sunday Oct 12th, 2008 10:03 pm Questions on Using Comfort > Upgrading comfort 1 Pro to Ultra (7 replies - 11340 views)
Chiu,
Can you advise where your copy of je21.bin can be downloaded....I have voice version 15 at present.
thanks
Campbell
... Saturday Oct 11th, 2008 11:39 am Comfigurator 3.x Old Versions (Archive) > New Template file requested (10 replies - 7896 views)
Chiu,
Can you advise if I was to convert this to File System 24, it would be suitable for use on Ultra I
thanks
Campbell
... Saturday Oct 11th, 2008 01:50 am FAQs - Technical > Comfort LSM (2 replies - 11472 views)
Does anyone have or can point me to where I can get a hold of one of these modules. I'm running out of zones on ... Friday Oct 10th, 2008 11:49 pm Questions on Using Comfort > Upgrading comfort 1 Pro to Ultra (7 replies - 11340 views)
I have now (at long last) fitted the "new" ultra A233 firmware in my Comfort 1 along with the U4 chip. if possible can you ... Saturday Oct 4th, 2008 12:05 pm Comfigurator 2.X > Comfort 1 Ultra - Comfigurator version (3 replies - 9921 views)
do the additional responses need to be added in notepad or other file editor as I can't see an obvious way of adding in Comfigurator. ... Saturday Oct 4th, 2008 11:53 am Miscellaneous Interfaces > Comfort and Visonic (8 replies - 18953 views)
Thanks Chiu,
I am intending mounting the MCR 308 approx 2 metres vertically up from the Comfort panel.
Am I right in thinking the Comfort is ... Saturday Sep 27th, 2008 05:01 pm Miscellaneous Interfaces > Comfort and Visonic (8 replies - 18953 views)
After a recent browse in my local alarm toyshop, I purchased all the
necessary bits (I think)to add the Visonic Wirefree to my Comfort 1
system and ... Saturday Sep 27th, 2008 10:21 am Questions on Using Comfort > Wireless alarm control/garage door operation (4 replies - 8156 views)
Many thanks....This could fit the bill....
I have a few Comfort Relays from playing with Camera switching back in 2000/2001 and if I can find these, ... Wednesday Jan 2nd, 2008 10:38 pm Comfigurator 2.X > Comfort 1 Ultra - Comfigurator version (3 replies - 9921 views)
I am considering re-writing all my responses for Comfort when I move from Pro to Ultra (Comfort 1).
Can anyone advise if it is still ... Wednesday Jan 2nd, 2008 10:29 pm Questions on Using Comfort > Wireless alarm control/garage door operation (4 replies - 8156 views)
Can anyone recommend a secure wireless interface for Comfort to
a/ Arm/disarm comfort to/from away mode
at the same time closing/opening the garage door "Hormann".
HAs anyone managed ... Wednesday Jan 2nd, 2008 12:27 am Questions on Using Comfort > Upgrading comfort 1 Pro to Ultra (7 replies - 11340 views)
Just wondering if you can give me the quick how to on upgrading... I purchased the A233 upgrade from Comfort UK last year but have ... Tuesday Jan 1st, 2008 04:34 pm |