we sent the ultra inorder to be check at your side any good news :) thanks ...   Tuesday Feb 25th, 2014 04:50 pm

Thant's a good news, thank you for your effort, as well,  i would appreciate if you could update the firmware for general UCM at your ...   Tuesday Feb 18th, 2014 05:52 pm

the unit been sent, i would like to correct one status :left led at RJ45(close to D101) blink 3 times then stop for 2 sec ...   Tuesday Feb 11th, 2014 05:37 pm

ETH02 Submodule for UCM was purchased at March 2012 as spare part item with part# (P056952) - invoice #C120100 ...   Monday Feb 10th, 2014 06:00 pm

my system is Cytech ultra2 with firmware upgraded to 7.047 and UCM/USB  board PC01-066A.I replaced daughter board with Eth02 board PC01-090A firmware 3.03. UCB firmware upgraded ...   Monday Feb 10th, 2014 05:37 pm

the serial-usb used to work fine before for a long time on the same operating system, even we tried a new one, but the same ...   Monday Jun 17th, 2013 12:31 pm

what i meant by connection: is "system information" check-up and it is not exactly 15 times , but around i'm using latest configrator V3.6.8 yes i meant ...   Tuesday May 14th, 2013 05:44 pm

i have a problem with UCM05, once a sudden it do not connect to cytech board, i tried another UCM05 and it made the same ...   Monday May 13th, 2013 12:52 pm

this is different case, i did the upgrade using file cytech3_13.bin, but still can not connect, " NO RESPONSE FROM UCM ", but i could ...   Thursday Oct 11th, 2012 03:38 pm

thanks for your fastest reply the ULT version is 6.020, and yes the daughter module was updated before the issue to firmware 3.13. the IDLE time set ...   Thursday Oct 11th, 2012 02:08 pm

another new issue concern UCM/ETH02, at one of our projects Eth02 connected for ipad interface, system ULT 6.2, UCM ver 6.012 the problem is that the ...   Thursday Oct 11th, 2012 11:27 am

i have an ULT ( firmware 6.28) Tibbe 5.8.5 i'm trying to upgrade the Etho2 as in picture, the configrator can not connect, Tibbo is connecting fine ...   Thursday Oct 11th, 2012 11:13 am

i would like to know how to connect Farfisa door station type PL41PCED to DM02, i'm quite not sure if it is possible to wire ...   Thursday Jun 14th, 2012 04:53 pm

Do you have a circuit diagram show the terminal connection of VR1 and which terminal we apply 3k ohm at ? ...   Thursday Jun 14th, 2012 12:54 pm

we replaced the speaker with 32ohm speaker ,0.5 watt, but it seem that the VR1 need to be replaced as well cause it been defected ...   Wednesday Jun 13th, 2012 05:23 pm

i need to replace the speaker for couple of DP03 which i don't hear a voice at all, i know that the speakers is 32-Ohm, ...   Wednesday Jun 13th, 2012 11:19 am

i need to make a response to be activated on a certain date, but i face the problem of power failure, when power failed as ...   Sunday Mar 18th, 2012 06:42 pm

we download the program but it works only on sending (0) value from the  universal kNX module (US/2) and doesn't works at all when it ...   Wednesday Feb 8th, 2012 07:56 am

first thanx for fast reply :) that was quick yes the switch on send ON value and the lighting modes is a combination between cytech ...   Friday Feb 3rd, 2012 12:52 pm

i had a request from a client to make one channel of KNX universal module triggering 6 sequence lighting mode, i need to share it ...   Friday Feb 3rd, 2012 12:17 pm

I'm using DP03, i upload tuning parameter only but with the same status, the problem occure only when i closed the back cover of the DP03  ...   Monday Jan 16th, 2012 11:56 am

I got a weird problem at two sites, I connect the door station by Cat5e cable to comfort v5.212, the sound between KP & DP ...   Sunday Jan 15th, 2012 04:49 pm

thanks for useful help, the situation now is: 7 Tws out of 10 was connected to slaves and LEM's and wasn't identify as Normal Open contact, ...   Sunday Jan 15th, 2012 12:48 pm

i had 5 TWS modules connected on lighting loads with consumption varied between 0.7Amp  to 3 Amp, those current sensor of TWS can not sense ...   Sunday Jan 8th, 2012 02:13 pm

The problem occurs at disconnecting group 2 and turned on only group 1, so there is no reflecting from surrounding ! ...   Tuesday Oct 25th, 2011 07:52 am

The problem that the fluor group 2 do not effect the doom but the group 1 (behind the doom ) is the one which effecting ...   Tuesday Oct 25th, 2011 06:24 am

ok attached illustration for common room ...   Monday Oct 24th, 2011 03:12 pm

results: - Doom that fixed on gypsum ceiling with fluorescent behind: we blocked the line of sight of  fluorescent , but still got the same error => no ...   Monday Oct 24th, 2011 02:31 pm

thanks, i will try right away but dose the fluorescent behind the Doom unit has any interfere effect (emf or whatever ? ...   Monday Oct 24th, 2011 02:09 pm

one our sites, rooms has Gypsum fall cieling (cave lighting) as a frame arround with a fluorescent inside, our doom located downside at one of ...   Monday Oct 24th, 2011 01:18 pm

observe reply ...   Tuesday Sep 6th, 2011 09:52 am

when the estimated time to be ready for ordering ...   Wednesday May 11th, 2011 11:51 am

Design B first Dedign c Design a ...   Monday May 9th, 2011 03:52 am

it's vantage , i don't have the type yet, i will post it once i got it , it is at site with one of ...   Monday Apr 4th, 2011 07:07 pm

thanks, i got what u meant but i want to clarify one thing the case that i have, the Lux sensor output is active , means ...   Sunday Apr 3rd, 2011 03:48 pm

what u mean by "Program the zone is Null Zone Type" ? and what will be the postion of zone Jumper ? ...   Sunday Apr 3rd, 2011 01:09 pm

i was clarifying  is there is a way to connect a Lux sensor with analogue output 0-3v to comfort input zone in order to use ...   Sunday Apr 3rd, 2011 11:59 am

first thanks for fastest reply and helpful response and info., as we always used and expect for CYTECH "Good Customers/partners support". secondly i need to clarify ...   Thursday Aug 26th, 2010 10:24 am

one of our clients had 2 Dome installed in his apartment, when we started to learned the Remote for TV simple couldn't, so i have ...   Tuesday Aug 24th, 2010 08:33 pm

what i meant is using UCM-KNX to interface comfort to the 11 KNX Busch-triton Switch ...   Wednesday Jun 30th, 2010 12:50 pm