Sorry, I should have been more specific. UCM02 is a CBus UCM. I tried a system reset both from the keyboard through the engineer menu, ...   Thursday Sep 27th, 2018 09:02 am

I have a Comfort II ultra with a UCM2 CBus board. It has run faultlesly for a few years then last night it failed to ...   Thursday Sep 27th, 2018 08:30 am

I have searched for a way to show sign in codes in plan text rather than obscured. I seem to remember that used to be ...   Friday Sep 14th, 2018 02:15 pm

Many thanks. I have installed the new version and the problem has gone away. Oddly though the version shown on the CSM has not changed ...   Saturday Dec 30th, 2017 04:10 pm

On 22nd December I noticed that the time on a door station was correct but the day was shown as 23rd. I reloaded the schedule ...   Friday Dec 29th, 2017 02:34 pm

Ben, you have pm. J ...   Monday Jun 19th, 2017 09:31 pm

I am intending to install Comfort in to a new house. My current configuration has hard wired PIR spread around the building, but in the ...   Friday Jun 9th, 2017 12:05 pm

There is no voice on sign in, so it seems that a vocab transfer is required. I assume I use myma.bin for that? ...   Tuesday Mar 14th, 2017 06:32 pm

I'm not sure if this is the correct area of the forum for this. I have recently uploaded an amended configuration file. It seems to be ...   Tuesday Mar 14th, 2017 12:21 pm

We are currently writing in to Comfort control of some swish curtains we have, and this has prompted some questions about the use and design ...   Friday Mar 10th, 2017 02:30 pm

I may be going potty in my old age, but I'm sure I remember a way controlling which events are included in the log file. ...   Thursday Mar 9th, 2017 04:35 pm

We think we have located the problem. The ethernet cable on the CBus unit was not making a good contact, so repeat sends were occuring. ...   Wednesday Mar 8th, 2017 10:58 am

We use CBUS to control curtain movement. The curtains are moved by a timer in C-Bus and also by pressing wall ...   Monday Mar 6th, 2017 04:19 pm

I was wondering if you are intending to create a presence on ITTT. It would be nice to send the security state to other software. ...   Monday Jan 30th, 2017 10:07 pm

This may go some way towards explaining my problems. I don't have the timekeeping checkbox on my copy (3.11.6). Wont I need to disable DST ...   Wednesday Oct 19th, 2016 10:22 am

OK, You have me. Where is the Timekeeping checkbox on the UCM/Cbus2 interface? ...   Tuesday Oct 18th, 2016 10:17 pm

That is a good question! From my experience C-bus has a random way of handling DST, it seems to move forwards or backwards by one hour ...   Tuesday Oct 18th, 2016 07:52 pm

I have both comfort and cbus running their own time systems, but have just upgraded to ETH03, which is a reliable system. I have always ...   Tuesday Oct 18th, 2016 01:19 pm

Thanks for all your help, I've found the problem. For future readers: I backed out of firmware 2.20 on ETH03 by overwriting it with 2.01, ...   Sunday Oct 16th, 2016 02:07 pm

I have just discovered a newer datasheet which has a paragraph entitled ' To reinitialise ETH03 to default settings. I have followed the instructions but ...   Sunday Oct 16th, 2016 01:09 pm

Yes, both D9 and D10 are flashing and all LEDs on the ethernet board are lit. I have pressed the reset button, but still no ...   Sunday Oct 16th, 2016 12:41 pm

Thanks for that Ingo. It just shows you can stare a an obvious error for hours and still not see it! Unfortunately it hasn't changed anything. ...   Sunday Oct 16th, 2016 10:42 am

I have just exchanged the ethernet controller to an ETH03, and at the same time upgraded the firmware to v2.20. The controller is a Comfort ...   Saturday Oct 15th, 2016 07:02 pm

I have an integrated comfort / Cbus setup. The cbus has a lux meter installed. Is it possible to get the lux meter to set ...   Sunday Oct 9th, 2016 01:33 pm

Thanks for your helpful comment. Does that mean that the DST won't work, or is there some other workaround? ...   Monday Sep 26th, 2016 01:36 pm

I have been having problems with random allocation of DST changes, so went to check the firmware version of the ETH03 module. I was surprised ...   Monday Sep 26th, 2016 12:58 pm

I have CSM 2.0.6 which will not connect upon refresh, and doesn't have a refresh button! I cn find Comfort on the network very easily ...   Tuesday Mar 31st, 2015 07:25 pm

I have downloaded the ETH03 firmware. How do I upgrade / insert this .hex file through configurator? ...   Sunday Mar 29th, 2015 01:08 pm

I have CBus for 90% of the lighting and other stuff, however there is no CBus device which I can use to control lamps which ...   Sunday May 4th, 2014 05:44 pm

I have written some code in CBus to operate curtains, this writes to a counter, which in turn has calls a response which will bypass ...   Saturday Apr 26th, 2014 12:54 pm

I understand, the 1 hour DS adjustment is assumed rather than explicit. Thank you. ...   Sunday Apr 20th, 2014 10:00 am

I have just installed 3.8.6.0 and find that it calculates sun set/rise times incorrectly. This error may have been in earlier versions but I cannot ...   Saturday Apr 19th, 2014 10:23 pm

Thank you all very much. I can see the way forward now. ...   Friday Dec 13th, 2013 07:58 am

ident wrote: I dont think cbus is able to send ASCII text but you can use a group address mapped to a counter Response to ...   Friday Dec 13th, 2013 06:30 am

I have a number of items controlled by Cbus, and also some by Comfort. The two communicate via the CBus UCM. Is it possible for ...   Thursday Dec 12th, 2013 06:46 am

Many thanks. ...   Tuesday Dec 10th, 2013 07:09 am

I am using Comfort to control my curtains, which means I need to bypass the PIRs which 'see' them. The code I have used has ...   Monday Dec 9th, 2013 11:55 am

I have and Ultra II and have calculated D&D times from Lat and Long. The problem is how to use the times. I wish to do ...   Thursday Nov 14th, 2013 01:03 pm

Thanks for that information, but could you be more specific? I am wishing to change some settings in CBus which depend upon whether Comfort is in ...   Monday Nov 4th, 2013 10:27 am

I have just installed a II ultra with CBus addon. All sorts of things are controlled by CBus. As CBus doesn't have flags which can ...   Friday Nov 1st, 2013 08:54 am