2nd message ...   Sunday Aug 14th, 2011 01:11 pm

There are two issues here. Happens every time. 1. The screenshot at the top. That error happens on EVERY odd attempt (ie attempt 1, 3, 5 ...   Sunday Aug 14th, 2011 01:10 pm

Hi Not quite correct. I've used the same 'code' for years. The CBUS UCM was changed in early 2010 and have been using that ...   Sunday Aug 14th, 2011 01:03 pm

Just the Universal UCM pops up in the list @ 6.003 ...   Sunday Aug 14th, 2011 07:27 am

On this page - http://comfortforums.com/forum92/2409.html It states "For Comfort, Slaves and "external" UCMs ie GSM, CBUS, KNX, Velbus, Universal, where the firmware is 6.000 and above, ...   Saturday Aug 13th, 2011 07:11 pm

What can we do to help get this resolved quickly ? ...   Friday Aug 12th, 2011 01:34 pm

I don't run toolkit except when re-configuring the system, or when looking at the log after this Comfort problem appears. The fact the previous firmware worked, ...   Friday Aug 12th, 2011 07:56 am

HI I was on that firmware before, and I didn't have that problem. Before I go through the pain of a downgrade, would Cytech like to debug ...   Friday Aug 12th, 2011 07:00 am

Hi, no physically - how would you populate the CBUS UCM with the AUD01 board, not what does it do. Thanks ...   Friday Aug 12th, 2011 06:58 am

Can I downgrade to the previous version which had no issues ? ...   Thursday Aug 11th, 2011 06:57 pm

I've got a strange issue where Comfort and CBUS occaisionally aren't talking - I have various CBUS buttons to kick off Comfort responses for critical ...   Thursday Aug 11th, 2011 06:56 pm

'External' ?? ...   Tuesday Aug 9th, 2011 11:37 am

FYI - I have 2 x UCM's @ 6.002 and 1 x UCM @ 6.003 ...   Tuesday Aug 9th, 2011 09:45 am

Same error on another PC trying to scan for modules in comfigurator ...   Tuesday Aug 9th, 2011 09:45 am

I have 3 UCM's which are viable candidates on the bus for an upgrade, all at v6.002 already. Only one gets listed as a possible candidate ...   Tuesday Aug 9th, 2011 09:44 am

Loaded again, and this time it goes through the process. Try again, the same error appears. V. odd ...   Tuesday Aug 9th, 2011 09:41 am

Downloaded Comfigurator 331, and wanted to upgrade the UCM's which are already at 6.002 Fired up Comfigurator, did a system information check (works fine) then proceeded ...   Tuesday Aug 9th, 2011 09:34 am

The same could be said of anything connected to a UCM over the network. The more layers you add, the more likely any single point ...   Tuesday Jul 5th, 2011 07:54 am

any plans to have these upgrade whilst live ala the new UCM firmwares ? ...   Monday Jul 4th, 2011 07:26 pm

I would still prefer a delay. If we are IN the house, we can hear the internal sounder - we don't need the phones to ...   Monday Jul 4th, 2011 07:25 pm

Home Easy / Bye Bye Standby / other RF products using the same protocol. That's a cheap solution once the Comfort U-UCM is released with ...   Tuesday Jun 14th, 2011 08:29 am

Do you have any further information on how the AUD01 works with a populated CBUS UCM please ? ...   Friday Jun 10th, 2011 01:42 pm

Assumption is that the UCM is v6 or higher before you can do this new method ? My 5.192 UCM refuses to upgrade using the new ...   Tuesday Jun 7th, 2011 05:27 pm

Seconded ...   Tuesday May 24th, 2011 07:41 am

to clarify - is the unit above the Clipsal C-Bus BS5000CT ? ...   Friday May 20th, 2011 01:52 pm

Be useful if you could recommend a suitable external speaker, or even re-use an existing or older Comfort unit/housing ...   Friday May 20th, 2011 01:49 pm

If this were to replace a KP04, for example, how would you handle audio feedback (speaker) ? ...   Wednesday May 18th, 2011 01:06 pm

Field testing with customers, perhaps ? ...   Friday May 13th, 2011 08:42 am

Any news please ? What challenges do you have if there's a hold up ? I now believe Cytech should have a Twitter account ;-) ...   Thursday May 12th, 2011 09:29 am

Time for Cytech to get started with an interface http://www.engadget.com/2011/05/11/lighting-science-demos-android-home-bulbs-promises-dead-simpl/ ...   Wednesday May 11th, 2011 03:39 pm

Can you disable the very annoying key beeps ? ...   Tuesday May 10th, 2011 04:58 pm

I cannot really distinguish them from these "photos". Either way, I would prefer a white version, or something that matches a CBUS Saturn DLT glass ...   Monday May 9th, 2011 08:04 am

Considering I currently have 'Alpha' and 'Beta' hardware from 2 very large well known electronic consumer organisations (one of which you will have either used ...   Monday May 9th, 2011 08:00 am

Perhaps a beta program would assist you with real world feedback ? ...   Friday May 6th, 2011 06:29 pm

Any update please ? Been a few months - are we able to buy the RFXCom and connect to a Universal UCM today ? ...   Tuesday Apr 12th, 2011 10:37 am

Is this because of rfxcom's new NDA on the protocol ? ...   Friday Mar 4th, 2011 06:16 am

Hi As you have the RFXCOM interface now, have you had any success in purely sending the commands from the UCM to the HomeEasy devices ? Thanks ...   Thursday Mar 3rd, 2011 01:51 pm

I believe RFXCOM are now in discussion with Cytech. IMHO, this "reverse" X10 RF protocol is one of the best - and my whole house ...   Monday Jan 31st, 2011 09:50 am

http://www.rfxcom.com/index.htm ...   Saturday Jan 29th, 2011 08:32 am

Did we get anywhere with this ? Will the modified firmware and/or the new U-UCM be able to control 4800bd, 8 bits data, no parity, ...   Saturday Jan 29th, 2011 07:06 am