Show Status, i think, show the status of a zone sensor eg Open / Closed in the Comfigurator Status panel and also on the Smart ...   Tuesday Nov 5th, 2013 09:56 am

You might want to try and 'default' the ETH2 card. Remove power from the UCM/ETH2 and re-apply whilst holding down SW101 for at least 7secs ...   Friday Oct 25th, 2013 12:29 pm

Do you have a 'link' light? (red led next to the RJ-45 socket). Suspect you do if you can ping it... In Comfigurator, is the IP ...   Friday Oct 25th, 2013 08:58 am

From recollection, Arduino uses either 3.3v or 5v TTL, so dependant on which board you use, the OP may need some extra circuitry Vangelis ...   Monday Sep 30th, 2013 08:06 am

Have you tried checking the IP address with Device Explorer (not Manager) from the Tibbo website? I had problems with seeng the IP address. Also ...   Thursday Sep 19th, 2013 01:58 pm

iPhone for sure will not connect to WiFi unless it's woken up by pressing the 'Home' button - not sure about Android. This is a power ...   Monday Sep 9th, 2013 12:36 pm

Assumption is that this question is related to Comfort and not generic... The keypads require STP connections but you can get away with non-shielded when connecting ...   Friday Aug 30th, 2013 11:27 am

Managed to upgrade both KP06 to 6.007 but after a power cycle I am seeing "Keypad NOT polled" on KP06 (ID2). This is the furthest keypad ...   Wednesday Aug 28th, 2013 06:08 pm

All fair points, and like you say, it is personal preference at the end of the day. I was just providing some feedback as requested :) ...   Friday Aug 23rd, 2013 09:32 am

I probably wasn't being very clear - Suggestion would be for some of the more important phrases eg Security State, or some important trouble alerts The ...   Thursday Aug 22nd, 2013 01:43 pm

Just started to play with the iPhone app and a possible amendment is the option to have the voice prompts come through the app - ...   Thursday Aug 22nd, 2013 08:19 am

Ok..progress..after reading the manual (doh) I found you could reset the ETH module by holding down SW101 for 7 secs on powerup (Now I know ...   Wednesday Aug 21st, 2013 03:59 pm

Superb (NOT) :( Now I think I have fubar'd the ETH2 Module by following the instructions... Fired up DS Explorer and it discovered my UCM (only the ...   Wednesday Aug 21st, 2013 03:41 pm

Hi Julian, Correct regarding the ETH Port light - the Yellow LED never lights unless I press SW101 and then the green LED goes out. After a ...   Tuesday Aug 20th, 2013 08:02 am

btw - I reseated the small ETH module and thats why it's not sitting on the PCB rider posts properly :) Suspect this will require warranty ...   Tuesday Aug 20th, 2013 06:33 am

One thing I did notice is that the Green LED on the ETH Socket flashes about once a second, and I would expect that to ...   Tuesday Aug 20th, 2013 06:32 am

Did some more testing last night but still with no luck, I am still unable to see the IP/MAC address of the UCM/ETH2 in the ...   Tuesday Aug 20th, 2013 06:28 am

Thanks... The HomeHub is an ADSL Router - I might power cycle that (as Julian suggested). My understanding, moving forward, is do NOT configure an IP address ...   Monday Aug 19th, 2013 10:56 am

Thanks Julian, Just seen the comment about the different IP subnetting not being an issue in http://www.comfortforums.com/forum92/3398.html So would you connect your PC direct to Comfort or ...   Monday Aug 19th, 2013 09:02 am

Running Comfort II Ultra with a UCM/Eth2 Needing to upgrade the firmware of both the Comfort and KP06 (see other thread) I finally got around to ...   Monday Aug 19th, 2013 07:48 am

Main Comfort Control unit interfacing with 3rd party LightwaveRF light switches PIRs can be used to turn on lights on entry, and when combined with some ...   Tuesday Aug 13th, 2013 10:20 am

Suspect you will need a little window for the IR LED. Black kinda gets away with it using a smoked window ...   Monday Aug 12th, 2013 03:10 pm

Thanks, will do that. Any issues with upgrading the ETH2 UCM module whilst your connected?? If the upgrade fails then surley you will lose comms to ...   Monday Aug 12th, 2013 12:29 pm

Hi there, Using Comfort Ultra II ver 6.002 Powered up after first fix installation.. All sensors connected Backup Battery No BellBox (SRNTMP shunted) No phone line (need to disable this in ...   Monday Aug 12th, 2013 06:41 am

Does the DVR have a network connection? (or capability?) If so it maybe as simple as putting in the IP address that the DVR is ...   Thursday Apr 4th, 2013 08:18 am

I'd be interested in this - as a DIY installer I am ok with the electric/electronics side of things but would benefit from a step-by-step ...   Tuesday Mar 19th, 2013 07:33 am

Has anyone played with this new hardware yet in conjunction with interfacing to Comfort?? I already have a Z-Wave UCM and was wondering how difficult they ...   Monday Mar 11th, 2013 10:32 am

No problem, I am just toying with the idea at the moment. I take your point regarding WinCE :D There are some neat in-wall touchscreen's around ...   Tuesday Jan 15th, 2013 10:46 am

juwi_uk Do you know if ComfortClient (.Net) will run on a moderate spec Tablet running Win CE or Linux. Have been looking at some in-wall devices. What ...   Tuesday Jan 15th, 2013 09:39 am

....is this unit still retailing aroung the 300 GBP mark? Is there a reason why the cost is so high? Doing a comparison with other ...   Friday Jan 11th, 2013 08:12 am

Thanks Ident - Is there a specific part number that I can specify in my email to a distributor to check they have the correct ...   Tuesday Jan 8th, 2013 08:20 am

...Is it 2 or 3? Reason I ask is that the UK distributors still reference GSM2 modules. If there is a 3, is there much ...   Monday Jan 7th, 2013 03:03 pm

They hold keys to your property - either a trusted neighbour, or alarm company. In an alarm situation where the owner cannot be contacted, then ...   Thursday Nov 29th, 2012 06:34 am

...include a GSM module and receive the alerts yourself (phone Police / Fire Brigade as required), ditch Red Care and save yourself some money...? ...   Tuesday Nov 20th, 2012 03:06 pm

If you planning to run multiple active bellboxes (as I am), then you might want to configure one as SAB and once as SCB. This ...   Tuesday Nov 20th, 2012 10:36 am

Yes it's the backlit box (for installer advertising). Be interested to know what the current draw of that feature is in case of loss of ...   Tuesday Nov 20th, 2012 08:23 am

12vf (according to wiring diagram) goes to Strobe +ve (which you don't have) Eng Hold is for installation - it allows you to tamper the bellbox ...   Tuesday Nov 20th, 2012 08:12 am

Alternatively pop the door contact out from the frame and carryout the test this way by disconnecting the wires. Be aware if there is tamper ...   Thursday Oct 25th, 2012 08:27 am

Think there was a write up on Automated Home a while back.. ...   Monday Oct 22nd, 2012 08:27 am

Check current draw of bell box under full alarm. If it exceeds Comforts current rating then you could switch it to SCB mode (if not ...   Tuesday Oct 2nd, 2012 12:07 pm