You may refer to the Comfigurator Reference Manual available from http://www.cytech-technology.com/temp/comfigman.pdf . There, the Comfort Configuration Language is explained. ...   Friday Sep 14th, 2007 04:54 am

Is the loss of the alarm message due to a voice download? ...   Wednesday Sep 12th, 2007 12:18 am

Questions: 1. What do you mean can't on/off? Do you mean to say the status on KT01 is not updated, resulting in wrong control? 2. What response ...   Tuesday Sep 11th, 2007 03:16 pm

By setting both your KT01 and C-Bus group addresses to the same, you will update the same counter in both cases, triggering the same counter ...   Tuesday Sep 11th, 2007 01:12 am

To have a sharper display on the KT01, turn off font smoothing. To do so: 1. Right-click anywhere on the desktop 2. Click "Appearance" tab 3. Click on "Effects" 4. ...   Monday Sep 10th, 2007 01:56 am

Just to add on to my earlier post, you may like to refer to the manual: http://www.cytech-technology.com/temp/irm01man.pdf . ...   Friday Sep 7th, 2007 02:55 pm

The IR02W is meant for shorter distances as compared to the IRM01. Moreover the IR02W is smaller in size, which would fit those using IR to ...   Friday Sep 7th, 2007 02:53 pm

We have identified a problem where WizComfort does not appear to load the CCL file contents correctly. This is caused by the CCL file being ...   Thursday Sep 6th, 2007 06:55 am

We have identified the problem which is caused by the CCL file being located in another PC on the same network and not on the ...   Thursday Sep 6th, 2007 06:53 am

I made a mistake: Should enter the Bind to IP to 0.0.0.0 instead of erasing. What values did you set them (the iomap and ifr directory) ...   Wednesday Sep 5th, 2007 12:04 am

The outputs tab is greyed out as I did not enable the settings. No problems after doing so. I noticed that you did not specify the ...   Tuesday Sep 4th, 2007 08:17 am

Here's the screenshot. ...   Tuesday Sep 4th, 2007 06:06 am

Don't seem to be facing the same problem. Could you send me the 2 ini files in the WizComfort directory? Thanks ...   Tuesday Sep 4th, 2007 06:04 am

Have you tried reselecting the ccl file under setup? If it still doesn't work kindly send the ccl file to me to investigate. ...   Tuesday Sep 4th, 2007 12:26 am

1. If you are using DHCP, then do not fill in that field. 2. Does your CCL file have a UCM defined as a CBUS type? ...   Monday Sep 3rd, 2007 08:38 am

It should be in Voice Settings not Tuning Parameters. Cheers ...   Monday Sep 3rd, 2007 12:07 am

Graham The default engineer code is 6789. You might want to refer to another thread for more information on the Engineer Code: http://www.comfortforums.com/forum20/698.html ...   Saturday Sep 1st, 2007 01:54 pm

Yes you can use the C-Bus switches to control Comfort outputs. This can be done by making use of the counter responses. The restriction would ...   Friday Aug 31st, 2007 12:09 am

Nope, there's no way to do so unless you want to create a super long response :P ...   Thursday Aug 30th, 2007 08:47 am

Hi Gary, We have already identified the problem. It is a problem with Comfigurator 2.2.1 and will be fixed in the next release. There is a way ...   Thursday Aug 30th, 2007 12:10 am

That should be a problem on the siren type settings. Try downloading the default siren type. ...   Monday Aug 27th, 2007 11:53 pm

Are you trying to reset the Ethernet plug-in? I'm afraid I do not think it is possible unless you are able to connect to it, ...   Wednesday Aug 22nd, 2007 08:50 am

I am pleased to announce the creation of a new UK voice. It is available from: http://www.cytech-technology.com/software_right.php?71 Note that the file is meant for use with Comfort ...   Wednesday Aug 15th, 2007 02:34 am

Do you mean to say you connected the TEL OUT to an extension line on the PABX? If so, the door station would not ring ...   Friday Aug 10th, 2007 06:02 am

EOL means End of Line Resistor These are the resistor values which must be connected to the sensor contact when the Zone shunts are set ...   Friday Aug 10th, 2007 05:10 am

From slychiu: Y?858F means 1st byte 85 is for outputs 1 to 8, 1st byte 8F is for outputs 9 to 16 The ...   Wednesday Aug 8th, 2007 06:08 am

Guess that is an oversight when creating the new menu for the various screens. Should be fixed in future. ...   Thursday Aug 2nd, 2007 08:55 am

If you want the output status of the RIO outputs, you should send y? and not Y? (note the lower case character) to query. As for ...   Thursday Aug 2nd, 2007 05:18 am

Y?0000 would mean all outputs 1-64 are all off. ...   Thursday Aug 2nd, 2007 02:50 am

Yes, the  Comfort firmware version 7.05x keeps the flags state unchanged after a system Reset BUT not after complete power off ...   Thursday Aug 2nd, 2007 02:46 am

Could it be due to the version of the UCM/main board? ...   Monday Jul 30th, 2007 08:47 am

You could make use of the Y? or y? commands instead then. ...   Monday Jul 30th, 2007 08:29 am

Doesn't the O? command work like you mentioned earlier? I would suggest that you change your program such that it would be able to handle ...   Monday Jul 30th, 2007 07:51 am

That action (Get ouput state) is meant for conditional programming and not meant for querying. ...   Monday Jul 30th, 2007 07:20 am

Could you verify whether the KP04's mic is working? It would seem to suggest that either the microphone is not working or your mic line is ...   Monday Jul 23rd, 2007 11:48 pm

No, VPG01 does not work with Comfort II. You will need a VPG02. However, note that there are differences in the vocabulary structure. You can refer ...   Saturday Jul 21st, 2007 08:16 am

Italian Residential is only for Comfort I not Comfort II. Note that selecting the vocabulary in Comfigurator does not make the system auotmatically switched to that ...   Saturday Jul 21st, 2007 12:09 am

Refer to an earlier post http://www.comfortforums.com/forum17/121.html Basically, the battery LED lights up every 10:15am due to a battery warning upon a 24-hour battery check. To disable the ...   Sunday Jul 15th, 2007 08:40 am

Glad to hear its working well! :) Cheers! :D ...   Wednesday Jul 11th, 2007 02:04 pm