Comfort Home Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register

Posts by ident
Profile Topics Posts
3493 postsShowing posts 121-160 of 3493

Questions on Using Comfort > KNX and AV control (1 reply - 4342 views)

You can learn IR codes into Comfort using a UCM/USB or UCM/Eth03 The IR codes can be sent to any Comfort output to control your AV The ...   Sunday Aug 10th, 2014 06:48 am

Troubles > Help to identify part-number (12 replies - 14148 views)

If all 3 sensors are connected to the same input, it could be that the sensors are normally open contacts so when any one is ...   Sunday Aug 10th, 2014 06:43 am

Universal UCM > UCM Universal (10 replies - 15339 views)

Currently the baud rates available are 2400, 4800, 9600, 19200, 38400, 76800 Other baud rates may be possible if the firmware is changed Which devices requires 57600 ...   Sunday Aug 10th, 2014 06:35 am

Zwave > Zwave and Cbus/other Lighting Platforms (28 replies - 30599 views)

There must be some zwave commands getting sent to Comfort which triggers the cbus ...   Friday Aug 8th, 2014 05:00 pm

Zwave > Zwave and Cbus/other Lighting Platforms (28 replies - 30599 views)

Try disabling the Zwave from the counter and see if that still occurs ...   Friday Aug 8th, 2014 04:18 pm

Ethernet UCM/ETH03 > New Features for UCM/ETH03 (29 replies - 13354 views)

Hmm, I assumed the email server did not require authentication ...   Friday Aug 8th, 2014 04:15 pm

Troubles > Help to identify part-number (12 replies - 14148 views)

We cannot  say if connecting the sensor to Comfort would work, without knowing how it works If it gives a relay contact then you can connect ...   Friday Aug 8th, 2014 03:57 pm

Troubles > Help to identify part-number (12 replies - 14148 views)

The photo on the left is not a UCM It is a Comfort or Slave The sensor is connected to Zone 2 of the comfort/slave Look for a ...   Friday Aug 8th, 2014 02:59 pm

Troubles > Help to identify part-number (12 replies - 14148 views)

That is not one of Cytech's products I do not know how it works with the UCM to send the flood alarm ...   Friday Aug 8th, 2014 05:38 am

Ethernet UCM/ETH03 > New Features for UCM/ETH03 (29 replies - 13354 views)

Try other alarms eg Dial Test by pressing F3 and 3 on the keypad Can you send a screenshot of your email setup on CS Manager? ...   Thursday Aug 7th, 2014 05:29 pm

Zwave > Zwave and Cbus/other Lighting Platforms (28 replies - 30599 views)

Howser wrote: If you have both Cbus and Zwave mapped to the same counter, when Cbus changes the counter, send a command to Zwave, ...   Thursday Aug 7th, 2014 10:00 am

Ethernet UCM/ETH03 > New Features for UCM/ETH03 (29 replies - 13354 views)

Also please log out from Comfigurator before testing the email function ...   Thursday Aug 7th, 2014 07:32 am

Ethernet UCM/ETH03 > New Features for UCM/ETH03 (29 replies - 13354 views)

We have tested your email server, and it has no problem with emails The Gateway should normally be your router IP address The DNS is normally your ...   Thursday Aug 7th, 2014 06:50 am

Zwave > Zwave and Cbus/other Lighting Platforms (28 replies - 30599 views)

If you have a counter that is mapped to both Zwave and Cbus, then changing the value of the counter will send commands to both ...   Thursday Aug 7th, 2014 06:28 am

Ethernet UCM/ETH03 > ETH03 Firmware History (13 replies - 20300 views)

ETH03 firmware 2.09 fixes a bug from firmware 2.02 whereTP time synchronisation sends the wrong value of the Month to Comfort, but the bug only ...   Tuesday Aug 5th, 2014 06:53 am

UCM/GSM Firmware > UCM/GSM 4 v7.053 (0 replies - 4617 views)

The new firmware UCM/GSM4 7.053 fixes a bug from GSM4 7.045 SMS to Control Menu 5 replies with control menu 1 text, even though the actions ...   Tuesday Aug 5th, 2014 06:48 am

UCM/CBUS Firmware > UCM/Cbus2 v7.052/7.054 (2 replies - 6992 views)

UCM/Cbus2 firmware 7.054 has been released Upgrade in Comfigurator by right clicking on the UCM/CBUS2 in Modules and selecting "Check for Updates" An Internet connection is needed ...   Tuesday Aug 5th, 2014 06:34 am

KP06A/KP04A Firmware > KP06 v6.009 (0 replies - 5225 views)

This firmware fixes a very specific bug which together with UCM/ETH03 firmware 2.02 to 2.08, only in the months of August and September, causes the ...   Monday Aug 4th, 2014 12:55 pm

Ethernet UCM/ETH03 > UCM/ETH03 cannot be seen in Comfort Server Manager (5 replies - 8198 views)

Discovery of ETH03 in Comfort Server Manager - Technical Information Comfort Server Manager uses UDP Port 30303 to discover the ETH03 IP address ETH03 will reply to ...   Sunday Aug 3rd, 2014 06:00 am

Ethernet UCM/ETH03 > UCM/ETH03 cannot be seen in Comfort Server Manager (5 replies - 8198 views)

Other causes of ETH03 not seen in CS Manager NOTE THAT COMFORT SERVER MANAGER CAN ONLY WORK ON  THE SAME NETWORK AS THE UCM/ETH03, NOT FROM ...   Sunday Aug 3rd, 2014 05:43 am

How to Use Comfigurator > Graphical References in Comfigurator (10 replies - 15599 views)

Graph References This is a feature in Comfigurator 3.9.5 which makes it easier to trace how Responses are used in Comfigurator Right Click on any Response and ...   Saturday Aug 2nd, 2014 08:39 am

CBus > Upgrading UCM/CBUS1 to UCM/CBUS2 (0 replies - 3384 views)

If you have UCM/Cbus1, you may be able to upgrade it to UCM/Cbus2 and take advantage of the powerful new features The procedure is shown at ...   Friday Aug 1st, 2014 07:03 pm

Ethernet UCM/ETH03 > UCM/ETH03 (10 replies - 16319 views)

Upgrading UCM Firmware, ETH03 Firmware, CS Manager Software The minimum UCM firmware which supports ETH03 is 7.048 If you are upgrading from USB or ETH02 to ETH03 ...   Friday Aug 1st, 2014 11:24 am

Problems & Troubleshooting > Possible bug with Sound Types (3 replies - 5572 views)

We can confirm that 151 Hz is actually the minimum sound frequency allowed Currently 0 or 150 to 2400 Hz is allowed The limit should be changed ...   Friday Aug 1st, 2014 10:46 am

Ethernet UCM/ETH03 > Heatmiser UCM, lightwave UCM and ETH03 (1 reply - 3858 views)

Universal UCM cannot be used for Heatmiser You need a Heatmiser UCM for that A  Universal UCM can only communicate with one type of 3rd party system ...   Friday Aug 1st, 2014 06:43 am

Universal UCM > LightwaveRF (9 replies - 13784 views)

Yes You can use Universal UCM + ETH03 for Lightwave RF ...   Friday Aug 1st, 2014 06:39 am

Heatmiser > Heatmiser UCM; can I use ETH03 rather than ETH02 (1 reply - 5121 views)

For wifi heatmisers, you need UCM/Heatmiser + ETH02 or UCM/Heatmiser+ETH03 can be used for Heatmiser wifi modules, not UCM06 which is for Comfigurator and ios/android apps However ...   Friday Aug 1st, 2014 06:36 am

CBus > UCM/CBUS2 Counter to Enable Control Application (9 replies - 14217 views)

For Howers original problem, the Cbus enable group will update the mapped counter and the Counter will update the enable group, ie 2 way operation ...   Thursday Jul 31st, 2014 05:19 pm

Comfort iPhone App (1st generation) > 2nd generation iPhone app - beta testing (2 replies - 7360 views)

This is the support forum for the new Comfort 2nd Generation iPhone app ...   Thursday Jul 31st, 2014 04:30 pm

Problems & Troubleshooting > Possible bug with Sound Types (3 replies - 5572 views)

It may be a bug which we have to check with R&D How low do you wish to set the frequency? 150 Hz is already quite ...   Thursday Jul 31st, 2014 04:24 pm

GSM Module > UCM Error LED on (8 replies - 11967 views)

Dont be sad You didnt just buy a replacement GSM module UCM/GSM4 is a completely new GSM module with better features and is much easier to use ...   Thursday Jul 31st, 2014 01:02 pm

GSM Module > UCM Error LED on (8 replies - 11967 views)

The status bar is actually not grayed out. It looks like the comfigurator window is positioned too low on the screen so the bottom line ...   Thursday Jul 31st, 2014 12:08 pm

Ethernet UCM/ETH03 > ETH03 Firmware History (13 replies - 20300 views)

The ETH03 (General) firmware version 2.08 can be downloaded from  http://www.cytech.biz/product_details.php?item_id=400 This fixes the bugs in the previous 2.06 firmware;IR Learner cannot work. Now IR learner ...   Thursday Jul 31st, 2014 09:21 am

CBus > UCM/CBUS2 Counter to Enable Control Application (9 replies - 14217 views)

UCM/Cbus2 7.054 now allows Changes in the mapped Enable counter to change the Cbus enable group and allows commands to the Enable and Trigger groups ...   Thursday Jul 31st, 2014 09:11 am

UCM/CBUS Firmware > UCM/Cbus2 v7.052/7.054 (2 replies - 6992 views)

UCM/Cbus firmware 7.054 (Beta) has the following changes; Fixed Bug - Enable and Trigger Group addresses did not update the mapped Comfort CountersFixed Bug - sending ...   Thursday Jul 31st, 2014 09:09 am

Questions on Programming Comfort > Interfacing with Axis Network Camera (4 replies - 9447 views)

Thanks for the update I have moved this to "Faqs - Technical" forum to facilitate easier searching and access for others looking for a similar interface ...   Thursday Jul 31st, 2014 07:13 am

GSM Module > UCM/GSM4 (1 reply - 9319 views)

The GSM status bar shows the current status of the UCM/GSM. The status bar can be seen on the bottom left of the GSM configurator ...   Thursday Jul 31st, 2014 07:09 am

GSM Module > UCM Error LED on (8 replies - 11967 views)

What sort of SIM Card did you use? Check that it is not a 3G only type like "3", and it is able to send ...   Thursday Jul 31st, 2014 06:59 am

CBus > UCM/CBUS2 Counter to Enable Control Application (9 replies - 14217 views)

We have found a bug in UCM/Cbus2 that Enable and Trigger applications do not activate the mapped counter This should be fixed in UCM/Cbus2 v7.053 http://www.cytech.biz/product_details.php?item_id=410 Please test ...   Wednesday Jul 30th, 2014 08:46 am

GSM Module > IPhone GSM SMS commander (3 replies - 3790 views)

Thanks for the link It does work and is quite simple to use ...   Wednesday Jul 30th, 2014 06:25 am


 Current time is 03:04 pm
 First Page Previous Page  1  2  3  4  5  6  7  8  9  ...  Next Page Last Page


UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems