Please see this topic which shows what is compatible and what must be upgraded Upgrading Comfort I to Comfort II - Module Compatibility http://www.comfortforums.com/forum16/1470.html ...   Monday Jun 2nd, 2014 01:10 pm

There is another bug causing phantom keypads 9 to 15 to appear after scanning  when Comfigurator 3.8.7 or 3.8.8 is used This is different from the ...   Monday Jun 2nd, 2014 08:57 am

How about getting the Family Care alarm to call you on your mobile instead? ...   Saturday May 31st, 2014 04:49 pm

why cant the panic button connect to a a Monitor N/O zone type 9 which triggers familycare alarm. This can cause dial out and can ...   Saturday May 31st, 2014 02:18 pm

Can you explain why you would need to wire the doorbell to a zone input instead of the DM02? the doorbell response is activated when the ...   Saturday May 31st, 2014 06:20 am

You need to connect the COM on the MCR308 to the 0V terminal on Comfort. You can also use the Zone Common between 2 adjacent ...   Friday May 30th, 2014 03:06 pm

Interesting related article here http://www.cepro.com/article/apples_centralized_home_controller_patent_suggests_apple_tv_as_home_automat/ ...   Friday May 30th, 2014 10:20 am

UCM/CBus2v 7.050 (beta) is available for testing. It can be downloaded from http://www.cytech.biz/ucmcbus2_firmware.html Changes Added new setting in UCM/CBUS2 to enable or disable the periodical resending of ...   Friday May 30th, 2014 09:42 am

UCM/Cbus2 v7.045 is the released version of UCM/Cbus2 Please note of the bug in the firmware which was recently discovered Known Bugs Enable and Trigger application map to ...   Friday May 30th, 2014 09:28 am

No it requires Comfort 2, or MinderPro2 Outside 4.222 is Comfort 1 I recommend an upgrade to Comfort2 as it enables  many new features like iOS/Android apps, ...   Friday May 30th, 2014 06:29 am

That would require a major change in the hardware and re-layout of the pcb and require an increase in cost, so less a significant number of ...   Thursday May 29th, 2014 03:46 pm

The speaker output is only connected to the siren sounds, and not the voice generation so Voice and announcements cannot ne heard from that The speaker ...   Thursday May 29th, 2014 06:38 am

Currentiy the email alarm message will report armed by user number, keypad, Response, SMS. we do not have an additional parameter available for keypad ID If ...   Wednesday May 28th, 2014 06:17 am

First, please do not post on more than 1 place. We will answer wherever it is Which keypad model is this, KP01, KO03, KP04, KP05, KP06, ...   Tuesday May 27th, 2014 05:52 am

This has already been answered here http://www.comfortforums.com/forum69/3056.html You do not need to post the same thing on more than 1 forum. Our support will answer the problems ...   Monday May 26th, 2014 03:31 pm

To see Comfort Server Manager, Go to Options > Settings > UCM Connection>  select UCM Interface = Network (Local). Click on Comfort Server Manager The ...   Monday May 26th, 2014 05:58 am

You can do it more simply that that This is the 1st Motion Detector Zone Response: If NightTime <> 0 Then     Do NullResponse After 30 Seconds Using ...   Sunday May 25th, 2014 11:06 am

With Comfigurator 3.8.8, the latest version of Comfort Server Manager can be updated automatically whenever you run CS Manager from Comfigurator Go to Options > Settings, ...   Sunday May 25th, 2014 08:43 am

The CS Manager 2.01 and UCM/ETH 2.06 are now released see http://www.comfortforums.com/view_topic.php?id=3695&forum_id=113 ...   Sunday May 25th, 2014 08:31 am

The UCM/ETH03 now supports these new features:Sending of emails to 4 email addresses for 31 Alarm Types. You can now be notified by email in ...   Sunday May 25th, 2014 08:29 am

The ETH03 firmware is NOT the same as the UCM firmware of the baseboard. The ETH03 firmware runs on the ETH03 submodule module and ...   Sunday May 25th, 2014 07:50 am

Another device for connecting UCM/ETH to the LAN are Homeplug from Aztech, TP-Link and other manufacturers http://www.aztech.com/sg/images/Products/HomePlug/HL113E_main2.jpg Two of these plug in devices are used. One is ...   Sunday May 25th, 2014 07:33 am

Can you start a new Post on your problem, and explain exactly what is the "Tamper Error" and when it happens This Topic is closed ...   Saturday May 24th, 2014 06:11 am

Optimum and SPC Firmware from 7.010 to 7.039 have the following bug Do Response action does not return Please avoid do Response actions Upgrade to Firmware ...   Friday May 23rd, 2014 02:50 pm

This could be due to the DTMF tones not detected by Comfort. It may be a sensitvity issue due to settings or due to the phone. ...   Friday May 23rd, 2014 12:34 pm

It has now been done ...   Friday May 23rd, 2014 06:03 am

You may have mixed up the engineer and user codes If you enter the engineer code on the phone or keypad, this enters Engineer Menu, not ...   Friday May 23rd, 2014 05:58 am

Look for the Response "Engineer Code enable" and press Execute This is the response activated by the F0 key ...   Friday May 23rd, 2014 05:51 am

1. In Comfigurator version 3.8.7 in both user and engineer mode, the real time updating of the zones/inputs stops most likely because of a bug. ...   Thursday May 22nd, 2014 01:24 pm

UCM 7.048 has been released from beta testing ...   Thursday May 22nd, 2014 10:07 am

Changes from 7.050 are Known Bugs Actions Add counter, Add counter give wrong answer from 7.039Engineer Code cannot be changed in the Engineer Menu 6 (from 6.008)Sending ...   Thursday May 22nd, 2014 09:49 am

ULT 7.057 has been released. See summary of changes in http://www.comfortforums.com/forum79/3815.html This fixes  the problem of extra keypads 9 to 15 appearing after a scan Please upgrade ...   Thursday May 22nd, 2014 09:27 am

I dont think "smart TVs" have any standard operating system for an app ...   Thursday May 22nd, 2014 07:07 am

By the way it is not necessary to post the question in several forums if the question fits into a few categories. We will answer ...   Thursday May 22nd, 2014 06:03 am

Did the system say Wrong code immedately or after you enter a code and # key? for the issue of ading keypads 9 to 15 see ...   Thursday May 22nd, 2014 05:56 am

Wizcomfort is being replaced by the new User Mode in Comfigurator 3.8 which will continue to be enhanced. Wizcomfort does not work with cclx files generated ...   Wednesday May 21st, 2014 04:43 pm

There is an isue with recent versions of Comfigurator or Wizcomfort. CCLX files created with recent versions of comfigurator can not be opened by wizcomfort. ...   Wednesday May 21st, 2014 04:26 pm

You can download from http://www.cytech.biz/knx_interface_training.html ...   Wednesday May 21st, 2014 04:09 pm

ULT 7.057 Beta can be tested at the above link The changes are Low Battery Trouble will report ID as 1 for Comfort controller to keep in ...   Wednesday May 21st, 2014 10:04 am

ComfortClient is mostly graphical, so which parts would you translate, the menus? Would that cause a maintenance problem, each time you update the software? ...   Wednesday May 21st, 2014 08:35 am