Its good to know the splitter was cauing the problem. If anyone else still has the problem of answering after two rings, let us have ...   Sunday Apr 15th, 2007 02:04 am

Clipsal developed an RF interface to the UCM for us,  as the UCM/Ulti allowing Comfort to send RF commands to the Ukti switches. Jung does not ...   Saturday Apr 14th, 2007 05:12 am

This is a picture of a competitors keypad which was sent to me as an example of an attractive keypad. Do others agree that Comfort ...   Saturday Apr 14th, 2007 02:30 am

The dome is not an IR distribution system like Xantech The IR receivers will only accept Comfort IR codes which will activate responses, it does not ...   Friday Apr 6th, 2007 01:17 am

Note that for Comfort II, the analog input range is 0 to 3V 5V analog inputs will cause no harm but they will be limited at ...   Thursday Apr 5th, 2007 10:05 am

Andy There is no such system with us for repair. They must be still in Cytech Europe being investigated regards ...   Thursday Apr 5th, 2007 06:33 am

How about using a Current sensor on the power lead of the Xbox to detect the current? This connects to a Comfort input and detects ...   Thursday Apr 5th, 2007 01:01 am

When there is an incoming call, you can immediately let the answering machine take the call by pressing # on the keypad. Comfort will answer ...   Sunday Apr 1st, 2007 11:02 am

V5.05 is not a valid firmware version, it may  be 5.05x there is another digit missing from the version You said that of 2 keypads, 1 ...   Sunday Apr 1st, 2007 10:15 am

Its not in Singapore - must be with Nigel ...   Sunday Apr 1st, 2007 08:02 am

Home wrote: Interesting  - I havve only just picked this thread up BUT we currently have an installation where a light sensor appears to be ...   Sunday Apr 1st, 2007 02:41 am

Can you tell me the Comfort firmware version? Perhaps get the customer to register on the forum so he can post direct? ...   Sunday Apr 1st, 2007 02:24 am

We are not familiar with Homegate so I cannot advise The Security Application 208 is implemented in the Comfort/MinderPro UCM/CBUS accprding to the CBus-enabled specifications. Hence ...   Sunday Apr 1st, 2007 02:21 am

Thats a nice video. However, Nigel mentioned that Cytech Europe is the distributor for UK AND Europe. This is not accurate, Cytech Europe is the ...   Saturday Mar 31st, 2007 04:04 am

Are you sure that OP4 is pulsing twice? Can you put a Test lamp on OP4 and see if it turns on two times? Or put ...   Saturday Mar 31st, 2007 03:27 am

I should have asked you to do a Battery test F3,1 - that may have cleared it ...   Friday Mar 30th, 2007 03:17 pm

What you have described shows that the zone is being retriggered, that is why the announcement of zone unsealed happens again and again Can you remove ...   Friday Mar 30th, 2007 05:59 am

This means that the zone which caused the alarm is being retriggered continuously This should be announced in the event log There may be a problem with ...   Friday Mar 30th, 2007 01:22 am

That is important because there has been changes in Comfort II for battery detection When you sign in on the keypad, do you get the Battery  ...   Thursday Mar 29th, 2007 01:09 am

The EN50131/PD6662 Guide for Comfort was released in the  installers forum on January 1st. This can be downloaded from http://www.cytech-technology.com/temp/techinfo/EN50131_PD6662.pdf This requires  new firmware Those who want ...   Wednesday Mar 28th, 2007 03:14 pm

The battery warning will flash when Comfort detects low battery This normally happens when the AC is off, unless the battery has gone bad and is ...   Wednesday Mar 28th, 2007 12:35 pm

If both the Red and Green LEDS on the Comfort PCB remain on after a reset, the whole system will not work. This means that there ...   Sunday Mar 25th, 2007 02:18 am

The German Research Centre for Artificial Intelligence was one of a growing group of exhibitors at this year's CeBIT showing how computer systems and AI ...   Friday Mar 23rd, 2007 11:27 am

Announcement from Yanza Yanza will be demonstrating their new Home Automation software at the Cytech Europe stand at the NEC from the 22nd to 25th March ...   Tuesday Mar 20th, 2007 12:21 pm

You use the Flash Output on a Slave. I am not sure if that willl cause a problem, we need to test this situation You say ...   Saturday Mar 17th, 2007 02:20 am

There is a thrid party Comfort Plug in for the Homeseer software, see http://www.comfortforums.com/forum28/ You will need the Homeseer software If you have any questions, you will ...   Friday Mar 16th, 2007 02:55 am

"Enjoy untethered WiFi control, cams and browsing anywhere in the home! View front door / nanny cams, control the media center, queue the movie and ...   Wednesday Mar 14th, 2007 01:38 pm

Which Comfort model you  have  and what is the firmware version written on the U1 label? Other than the keypad message, does the keypad work ...   Monday Mar 12th, 2007 11:39 am

The beta firmware Ultra 5.087 for EN50131/PD6662 compliance was available at the beginning of February. Has anyone had this for testing and if so, is ...   Monday Mar 12th, 2007 02:28 am

The picture of Scotts mockup was not visible when I replied. Nice work! The slotted speaker holes should be no problem, not sure how the ...   Saturday Mar 10th, 2007 09:38 am

The new version of the LSM Manual 1.0.2 is available on the website http://www.cytech-technology.com/manuals.html We do not manufacture the LSM01 anymore, as the Sunrise/Sunset feature for ...   Saturday Mar 10th, 2007 05:33 am

The revised version of the LSM Manual 1.02 is available on http://www.cytech-technology.com/manuals.html This describes the timer delay program to help prevent multiple switching of the LSM ...   Saturday Mar 10th, 2007 05:29 am