+- Comfort Automation/ Security System Forums (https://www.comfortforums.com)
+-- Forum: Third Party (interfacing to Comfort) (https://www.comfortforums.com/forum-5.html)
+--- Forum: CBus (https://www.comfortforums.com/forum-11.html)
+---- Forum: UCM/CBUS Problems (https://www.comfortforums.com/forum-120.html)
+---- Thread: Tracking Responses sending Cbus Commands (/thread-5110.html)
Pages:
1
2
- Howser - 09-07-2019
I am using Comfigurator with Comfort 2Z Ultra (v 7.160), Cbus2 Ucm (v7.106)
Code:
DateTime= 2019/09/07 20:56:35.245 App= 202 Trigger Control Group= 014 Kitchen Unit= 008 PC_CNIEI/INL_CNI Event= Action Selector triggered : 50, \'Motion-AutoLights OFF\'
DateTime= 2019/09/07 20:56:35.629 App= 056 Lighting Group= 039 Kitchen Light 1 Unit= 009 PC_PACA/MOHAUPAC Event= Group ramped to 063 ( 25%) over 12 seconds
DateTime= 2019/09/07 20:56:35.632 App= 056 Lighting Group= 040 Kitchen Light 2 Unit= 009 PC_PACA/MOHAUPAC Event= Group ramped to 073 ( 29%) over 30 seconds
DateTime= 2019/09/07 20:56:38.386 App= 056 Lighting Group= 039 Kitchen Light 1 Unit= 127 EN_CMFT/COMFORT Event= Group ramped to 064 ( 25%) over 0 seconds
DateTime= 2019/09/07 20:56:38.598 App= 202 Trigger Control Group= 014 Kitchen Unit= 009 PC_PACA/MOHAUPAC Event= Trigger Indicator KillI have included a log (above) from Cbus Toolkit which shows Comfort Ucm/Cbus (EN_CMFT/COMFORT) ramping Kitchen Light 1 to 25% over 0 seconds after a trigger event is raised.
I tried looking at all the responses where Kitchen Light One is referred to and for the life of me, I cannot track where in Comfort this occurs.
- slychiu - 09-08-2019
Can you send the cclx file to support@cytech.biz?
- Howser - 09-08-2019
Done, cclx file sent support@cytech.biz.
- slychiu - 09-08-2019
I do not see any where the Counter 39 is changed by any response or otherwise
Note that changing Counter 39 value will also send the counter value to Cbus Eg if counter 39 is changed to 256/4 = 64 then that causes the Cbus deive to ramp to 25%
Turn on Monitor I/O before doing the trigger, then look for CT27 report in the monitor. This may give a clue to what caused itIt may be UCM/Pi changing the counter
- Howser - 09-08-2019
This is what the monitor shows
< CT273F00
< CT284900
< CT279900
< CT28A500
< CT274000
< CT284A00
- slychiu - 09-09-2019
< CT273F00 means the counter 39 is changed to 64That accounts for cbus lighting group address 39 going to 25%
I cant see from your responses that coumnter 39 is changed to this value. There shoukl be something else causing this. Could it be the Cbus
Go to Tools > Bus Monitor and press Start before the trigger. Then copy theBus monitor
- Howser - 09-09-2019
Find attached the bus Monitor.
- slychiu - 09-10-2019
This is the relevant message in Bus Monitpr
[color=\"#ff0000\"] 21: 40: 57: 945 ----< 03 12 71 32 37 33 46 31 34 02 <--->q273F14[/color]
21: 40: 57: 965 ----< 03 00 64 32 37 33 46 30 30 31 32 32 31 02 <--->/d273F001221
The line is red means UCM ID #2 sent Counter 39 value 3F ie 64.
Comfort broadcast the counter 39 value = 3F
Counter 37 is mapped to Lighting Group address 39. Hence when UCM/Cbus receives the message from group 39 from Cbus, it sends the Counter value to Comfort
- Howser - 09-10-2019
I have
- Cbus GA 39 (Kitchen Light 1) mapped to Counter 39 and
- Cbus GA 40 (Kitchen Light 2) mapped to Counter 40.
My question is why Comfort re broadcasting GA 39, and why only GA 39?
I thought UCM ID#2 will only update the Counter 39 and 40 in Comfort, and not broadcast their values back to Cbus?
- slychiu - 09-10-2019
Quote:I thought UCM ID#2 will only update the Counter 39 and 40 in Comfort, and not broadcast their values back to Cbus?
That is correct. UCM/Cbus will not send the values back to Cbus which was received from Cbus.
Go to the UCM/Cbus2 Monitor Mode. This will show the transmit and receive messages
> means transmit line, < means receive line
You can confirm here if CM/Cbus is resending to Groups 39 and 40