<![CDATA[Comfort Automation/ Security System Forums - RIO Firmware]]> https://www.comfortforums.com/ Sun, 09 Aug 2026 01:50:18 +0000 MyBB <![CDATA[RIo Firmware 2.007 to 2.009]]> https://www.comfortforums.com/thread-2697.html Fri, 20 Jan 2012 22:00:23 -0500 ]]> https://www.comfortforums.com/thread-2697.html Version 2.009 - 25 April 2011

  1. Removed Warm Reset. All resets are cold resets now (ie. ID is read and all outputs are reset to off). No need to disconnect power when ID is changed, just press Reset button on RIO
Version 2.008 - 17 June 2010
  1. Supoort for Unknown command on RS485 Bus (21H)
Version 2.007 - 18 December 2007
  1. Resolved the problem that \"When shunt R at J2 is in open position, shorting any input won\'t make its corresponding output (connected to test bulb) to flash continuously\" as it should in normal operation.
]]> Version 2.009 - 25 April 2011

  1. Removed Warm Reset. All resets are cold resets now (ie. ID is read and all outputs are reset to off). No need to disconnect power when ID is changed, just press Reset button on RIO
Version 2.008 - 17 June 2010
  1. Supoort for Unknown command on RS485 Bus (21H)
Version 2.007 - 18 December 2007
  1. Resolved the problem that \"When shunt R at J2 is in open position, shorting any input won\'t make its corresponding output (connected to test bulb) to flash continuously\" as it should in normal operation.
]]> <![CDATA[RIO Firmware 2.0.0 to 2.0.6]]> https://www.comfortforums.com/thread-1092.html Sat, 14 Jun 2008 01:44:49 -0400 ]]> https://www.comfortforums.com/thread-1092.html
  • [size=2]2.0.6 (Dec 2007) Supports Pulse Output action. Previous versions do not support Pulse Outputs
  • 2.0.4 (March 2007) CBUS2 IR Codes supported, mapped in IRReceive codes 0-31. Adjusted IR Receive algorithm to match new IR Receiver characteristic.
  • 2.02 (May 2005) Fixed Bug in previous versions where noise on an input may cause the RIO to lock up until the input is triggered again
  • 2.0.1 (June 2004) Fixed IR Transmission can transmit IR 0 to 255. Fixed bug could only transmit 0-15
  • 2.0.0 (Dec 2003) - Upgraded processor. Transmit IR 0 to 15 only. IR Transmit buffer increased from 64 to 96
The Firmware history is also documented in the RIO Manual
[/size]]]>
  • [size=2]2.0.6 (Dec 2007) Supports Pulse Output action. Previous versions do not support Pulse Outputs
  • 2.0.4 (March 2007) CBUS2 IR Codes supported, mapped in IRReceive codes 0-31. Adjusted IR Receive algorithm to match new IR Receiver characteristic.
  • 2.02 (May 2005) Fixed Bug in previous versions where noise on an input may cause the RIO to lock up until the input is triggered again
  • 2.0.1 (June 2004) Fixed IR Transmission can transmit IR 0 to 255. Fixed bug could only transmit 0-15
  • 2.0.0 (Dec 2003) - Upgraded processor. Transmit IR 0 to 15 only. IR Transmit buffer increased from 64 to 96
The Firmware history is also documented in the RIO Manual
[/size]]]>