Register Account

Comfort Automation/ Security System Forums Third Party (interfacing to Comfort) KNX (EIB) KNX Support

KNX Support
Thread / Author [asc] Rating Replies Last Post
   
Go to first unread post UCM/KNX in Monitor Mode
Thread started by ident
Replies: 2
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 22,382 		09-22-2016, 06:15 AM
Last Post: slychiu
   
Go to first unread post Counters (1-Bit) -> KNX
Thread started by Home
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 8,615 		02-27-2019, 04:10 AM
Last Post: slychiu
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 12
Views: 32,711 		12-10-2011, 05:18 AM
Last Post: ident
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 12,234 		11-25-2013, 02:12 PM
Last Post: evard
   
Go to first unread post UCM/KNX power failure alarm
Thread started by ekarak
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 10,014 		12-06-2010, 12:07 PM
Last Post: slychiu
   
Go to first unread post spurious KNX packets from Comfort
Thread started by ekarak 1 2
Replies: 16
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 16
Views: 41,286 		09-07-2012, 03:07 AM
Last Post: ident
   
Go to first unread post UCM/KNX race condition
Thread started by ekarak
Replies: 4
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 4
Views: 14,244 		04-16-2016, 05:22 PM
Last Post: ekarak
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 11,379 		01-22-2011, 06:18 AM
Last Post: slychiu
   
Go to first unread post KNX temperature readout in Comfort
Thread started by ekarak 1 2
Replies: 11
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 11
Views: 33,766 		09-07-2012, 03:07 AM
Last Post: ident
   
Go to first unread post UCM2 is not a UCM/KNX2
Thread started by davidsilva
Replies: 5
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 5
Views: 16,944 		03-18-2017, 06:41 AM
Last Post: slychiu
   
Go to first unread post Disarming Alarm KNX
Thread started by Canha 1 2
Replies: 12
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 12
Views: 34,684 		10-12-2011, 01:19 PM
Last Post: Canha
   
Go to first unread post UCM/KNX Virtual Input Question
Thread started by auredor 1 2
Replies: 12
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 12
Views: 31,396 		02-22-2012, 04:10 AM
Last Post: ident
   
Go to first unread post UCM / KNX group adress limitations
Thread started by auredor
Replies: 6
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 6
Views: 19,756 		08-24-2012, 03:13 AM
Last Post: ident
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 9
Views: 36,747 		08-25-2011, 09:51 PM
Last Post: mario.jr
   
Go to first unread post Communication KNX-Cytech problem
Thread started by agenor 1 2
Replies: 13
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 13
Views: 19,654 		09-30-2012, 02:53 AM
Last Post: ident
   
Go to first unread post Upgrading UCM/Knx
Thread started by agenor
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,901 		02-05-2015, 08:59 PM
Last Post: tman
   
Go to first unread post D4 “ERROR”
Thread started by Guest
Replies: 9
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 9
Views: 19,921 		01-05-2008, 08:01 PM
Last Post: marinoss


Forum Jump:


Users browsing this forum:
7 Guest(s)

Powered By MyBB, © 2002-2026 Melroy van den Berg.