Register Account

Comfort Automation/ Security System Forums Third Party (interfacing to Comfort) KNX (EIB) KNX Support

KNX Support
Thread / Author Rating Replies [asc] Last Post
   
Go to first unread post UCM/KNX Monitor Mode
Thread started by Tan121
Replies: 3
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 3
Views: 13,115 		02-18-2013, 07:09 PM
Last Post: juwi_uk
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 3
Views: 12,456 		12-31-2011, 07:00 AM
Last Post: ident
   
Go to first unread post UCM/KNX with C-Bus to KNX Translator
Thread started by mgedrych
Replies: 3
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 3
Views: 22,062 		09-18-2020, 05:03 AM
Last Post: slychiu
   
Go to first unread post Incomplete zone status to KNX
Thread started by Stefan
Replies: 3
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 3
Views: 12,685 		01-10-2017, 03:28 AM
Last Post: Stefan
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 11,540 		11-25-2013, 02:12 PM
Last Post: evard
   
Go to first unread post UCM/KNX in Monitor Mode
Thread started by ident
Replies: 2
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 21,689 		09-22-2016, 06:15 AM
Last Post: slychiu
   
Go to first unread post KNX Programming via Comfort
Thread started by rhennessysummit
Replies: 2
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 10,404 		01-09-2018, 03:49 PM
Last Post: slychiu
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 10,843 		01-22-2011, 06:18 AM
Last Post: slychiu
   
Go to first unread post KNX UCM
Thread started by paulkgrace246
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,771 		11-16-2015, 04:53 PM
Last Post: slychiu
   
Go to first unread post Upgrading UCM/Knx
Thread started by agenor
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,383 		02-05-2015, 08:59 PM
Last Post: tman
   
Go to first unread post Bypass zone from KNX
Thread started by Stefan
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 8,348 		08-29-2017, 07:28 AM
Last Post: slychiu
   
Go to first unread post Counters (1-Bit) -> KNX
Thread started by Home
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 8,095 		02-27-2019, 04:10 AM
Last Post: slychiu
   
Go to first unread post ETS configuration
Thread started by philip@measolutions.co.za
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,481 		07-30-2012, 09:41 AM
Last Post: ident
   
Go to first unread post UCM/KNX power failure alarm
Thread started by ekarak
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,629 		12-06-2010, 12:07 PM
Last Post: slychiu
   
Go to first unread post KNX Support Subforums
Thread started by ident
Replies: 0
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 18,012 		10-05-2012, 12:45 PM
Last Post: ident
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 7,851 		09-15-2012, 03:01 AM
Last Post: ident
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 7,386 		08-21-2012, 12:33 PM
Last Post: ident


Forum Jump:


Users browsing this forum:
8 Guest(s)

Powered By MyBB, © 2002-2026 Melroy van den Berg.