Register Account

Comfort Automation/ Security System Forums Third Party (interfacing to Comfort) KNX (EIB) KNX Support

KNX Support
Thread / Author Rating [asc] Replies Last Post
Important Threads
   
Go to first unread post Error writing to KNX
Thread started by slychiu
Replies: 0
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 7,691 		01-21-2018, 07:18 AM
Last Post: slychiu
   
Go to first unread post Bug in Comfigurator 3.11.0 to 3.11.1
Thread started by slychiu
Replies: 0
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 6,898 		04-18-2016, 03:55 PM
Last Post: slychiu
   
Go to first unread post How to Send Date and Time to KNX
Thread started by slychiu
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 10,568 		02-23-2010, 09:13 AM
Last Post: slychiu
   
Go to first unread post UCM/KNX Action Problem
Thread started by slychiu
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 11,136 		12-11-2009, 05:58 PM
Last Post: ident
Normal Threads
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 7,848 		09-15-2012, 03:01 AM
Last Post: ident
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 7,381 		08-21-2012, 12:33 PM
Last Post: ident
   
Go to first unread post KNX Support Subforums
Thread started by ident
Replies: 0
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 0
Views: 18,011 		10-05-2012, 12:45 PM
Last Post: ident
   
Go to first unread post UCM/KNX in Monitor Mode
Thread started by ident
Replies: 2
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 21,682 		09-22-2016, 06:15 AM
Last Post: slychiu
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 11,536 		11-25-2013, 02:12 PM
Last Post: evard
   
Go to first unread post Upgrading UCM/Knx
Thread started by agenor
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,380 		02-05-2015, 08:59 PM
Last Post: tman
   
Go to first unread post KNX UCM
Thread started by paulkgrace246
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 9,771 		11-16-2015, 04:53 PM
Last Post: slychiu
   
Go to first unread post UCM/KNX race condition
Thread started by ekarak
Replies: 4
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 4
Views: 13,179 		04-16-2016, 05:22 PM
Last Post: ekarak
   
Go to first unread post Incomplete zone status to KNX
Thread started by Stefan
Replies: 3
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 3
Views: 12,679 		01-10-2017, 03:28 AM
Last Post: Stefan
   
Go to first unread post UCM2 is not a UCM/KNX2
Thread started by davidsilva
Replies: 5
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 5
Views: 15,678 		03-18-2017, 06:41 AM
Last Post: slychiu
   
Go to first unread post Bypass zone from KNX
Thread started by Stefan
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 8,342 		08-29-2017, 07:28 AM
Last Post: slychiu
   
Go to first unread post KNX Programming via Comfort
Thread started by rhennessysummit
Replies: 2
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 2
Views: 10,396 		01-09-2018, 03:49 PM
Last Post: slychiu
   
Go to first unread post Counters (1-Bit) -> KNX
Thread started by Home
Replies: 1
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 1
Views: 8,092 		02-27-2019, 04:10 AM
Last Post: slychiu
   
Go to first unread post UCM/KNX with C-Bus to KNX Translator
Thread started by mgedrych
Replies: 3
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 3
Views: 22,056 		09-18-2020, 05:03 AM
Last Post: slychiu
   
Go to first unread post D4 “ERROR”
Thread started by Guest
Replies: 9
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 9
Views: 19,852 		01-05-2008, 08:01 PM
Last Post: marinoss
   
  • 0 Vote(s) - 0 out of 5 in Average
 Replies: 9
Views: 23,265 		12-10-2011, 04:23 AM
Last Post: ident


Forum Jump:


Users browsing this forum:
7 Guest(s)

Powered By MyBB, © 2002-2026 Melroy van den Berg.