+- Comfort Automation/ Security System Forums (https://www.comfortforums.com)
+-- Forum: Third Party (interfacing to Comfort) (https://www.comfortforums.com/forum-5.html)
+--- Forum: Zwave (https://www.comfortforums.com/forum-62.html)
+--- Thread: Zone and Zwave Feedback (/thread-2595.html)
- lwillerton - 11-12-2011
Hi,
I want to know the state of my Z-Wave lamps and some alarm zones via the Iphone app or by calling the system.
I have been told how to do it, but still not really figured it out. So if anyone can help me get this working I would appreciate it.
Cheers
Lee
- schford - 11-12-2011
Not sure about Z wave - but for the alarm zones - go to https://www.cytech.biz/crl_test.php
Load up your cclx then open the email it sends you on your iphone, this will store all your zones in the comfort app on the iphone.
Then when you log into the iphone app - you can go to the zones tab and see the current state of all the zones.
Stuart
- lwillerton - 11-12-2011
Cheers Schford....
That works great on the iPhone, how about if I call the system on the phone?
Hopefully some else will have an idea on the Z-wave side of things. BTW Z-Wave works great with the sytem.
- tech07 - 11-13-2011
Z-Wave state can see on the iPhone app.
See UCM/Zwave Manual, tells you how to have feedback of zwave in Counters. Use Zwave Configurerator to assign Counter to Zwave address, see photo http://www.comfortforums.com/forum62/1417.html
Make Home Control Menu for control Z-Wave and put Feedback Type as Counter, select the Counter mapped to the Z-Wave address.
Send the cclx file to iPhone by email using the same https://www.cytech.biz/crl_test.php
In iPhone Home Control Page will show the Zwave device status
But the status for Z-Wave is update every 10 seconds
- tech07 - 11-13-2011
To hear the state of zones using telephone, go to Security Check menu, 3,4,2. It announce all zones that are ON (open) and not zones that are OFF
To hear control menu status on phone, do 4 for Home Control and press key for controled devices like Zwave and menu will announce ON, OFF or level
- lwillerton - 11-13-2011
Hi Tech07
Thanks for the pointers, looks like that should sort it.
Cheers
Lee
- lwillerton - 11-13-2011
Hi Tech07 (1 of 3)
I have setup the following. However, I don\'t seem to be able to setup multiply counters under the the module section. Not sure if that is necassery or not.
I am using HomePro Z-Wave lamp plugins and an Aeon Labs Z-Stick Serise 2 and the main interface. To be honest I have stopped using the Z-Stick and just use this to program the Cytech system.
Before I run the config through for the iPhone is there any way I can test? Should the status change on the control menu?
Cheers Lee
- lwillerton - 11-13-2011
(2 of 3)
- lwillerton - 11-13-2011
(3 of 3)
- ident - 11-14-2011
You have set up Zwave ID 2 assigned to Counter 1 as feedback. Control menu 0 for Lights > 1 for Lounge lamp will control the Zwave ID
This is correct. The counter will store the state of the Zwave ID
Hence if you go to keypad F2 0 for Lights, 1 for Lounge lamp you wll hear \"Lounge Lamp is \" OFF or ON or level 0 to 99
You dont have to set up Multiple counters, just 1 counter per Zwave devjce
However the Zwave status is updated once only every 10 seconds depending on the setting