https://www.comfortforums.com/ Mon, 27 Jul 2026 10:44:17 +0000 MyBB https://www.comfortforums.com/thread-5811.html Tue, 14 Oct 2025 03:19:21 -0400 slychiu]]> https://www.comfortforums.com/thread-5811.html Comfigurator 4 can be installed with  Comfigurator 3.x.x in the PC, This allows  the old comfigurator 3 to be used eg with old cclx files if necessary due to compatibility problems

Known Bugs

• when  upgrading firmware ;after logging in and right clicking on Controller to  "upgrade firmware from local file" and selecting the cbf file, the message "CBF file not compatible with the firmware to be upgraded" is seen, but after a scan for modules  then it can upgrade. Also if start a new template, an  upgrade can be done without any error message.
  
• if comfort is Optimum firmware, opening ULT or EMS file system and connecting and logging in to the system will get exception. This will not happen for EMS or ULT. Normally iComfigurator should warn that the file system is not matched to the firmware
  
• When  firmware upgrade fails, for any reason and there is an attempt to upgrade again,  Comfigurator log in fails because many commands are sent at log in while UCM in bootmode can only reply to 1 command at a time.
  
• After log in if ther eis no  scan for modules, download firmware upgrade will select the non-arm firmware
  
• Scan for Modules sometimes gets error "Scan for Modules failed"
  
• Write to Sunset Response writes 0 instead of the response number so sunset response does not work
  

Bugs Fixed

• Corrupted cclx files were sometimes scanned wrongly as ARM
  
• Phone numbers screen  does not show sms permissions when 1st phone is not Voice or SMS (eg phone is is CMS)
  
• HIO could not be detected after scan for modules
  
• fixed bugs with multiple repeated outputs in responses or displayed Outputs in Comfort register
  
• fixed bug with UCM ID 0 or 1  wrongly detected when there is a plug in ETH03 in CM9001
  

Changes

• In Zones "Duplicate EOL settings" checkbox shows a warning message before confirming so the box is not checked by mistake
  
• supports new  gsm5 module
  

]]> Comfigurator 4 can be installed with  Comfigurator 3.x.x in the PC, This allows  the old comfigurator 3 to be used eg with old cclx files if necessary due to compatibility problems

Known Bugs

• when  upgrading firmware ;after logging in and right clicking on Controller to  "upgrade firmware from local file" and selecting the cbf file, the message "CBF file not compatible with the firmware to be upgraded" is seen, but after a scan for modules  then it can upgrade. Also if start a new template, an  upgrade can be done without any error message.
  
• if comfort is Optimum firmware, opening ULT or EMS file system and connecting and logging in to the system will get exception. This will not happen for EMS or ULT. Normally iComfigurator should warn that the file system is not matched to the firmware
  
• When  firmware upgrade fails, for any reason and there is an attempt to upgrade again,  Comfigurator log in fails because many commands are sent at log in while UCM in bootmode can only reply to 1 command at a time.
  
• After log in if ther eis no  scan for modules, download firmware upgrade will select the non-arm firmware
  
• Scan for Modules sometimes gets error "Scan for Modules failed"
  
• Write to Sunset Response writes 0 instead of the response number so sunset response does not work
  

Bugs Fixed

• Corrupted cclx files were sometimes scanned wrongly as ARM
  
• Phone numbers screen  does not show sms permissions when 1st phone is not Voice or SMS (eg phone is is CMS)
  
• HIO could not be detected after scan for modules
  
• fixed bugs with multiple repeated outputs in responses or displayed Outputs in Comfort register
  
• fixed bug with UCM ID 0 or 1  wrongly detected when there is a plug in ETH03 in CM9001
  

Changes

• In Zones "Duplicate EOL settings" checkbox shows a warning message before confirming so the box is not checked by mistake
  
• supports new  gsm5 module
  

]]> https://www.comfortforums.com/thread-5649.html Tue, 01 Jul 2025 16:35:29 -0400 Howser]]> https://www.comfortforums.com/thread-5649.html
I am using version v3.14.14.0

  Comfort Output Issue.png (Size: 30.3 KB / Downloads: 19) ]]>
I am using version v3.14.14.0

  Comfort Output Issue.png (Size: 30.3 KB / Downloads: 19) ]]> https://www.comfortforums.com/thread-5635.html Fri, 16 May 2025 03:34:17 -0400 ]]> https://www.comfortforums.com/thread-5635.html Comfigurator installation requires .NET 3.5 to be installed, and will prompt for download and installation if it is not found on the PC.

When you try to install the downloaded .NET3.5 you may get a message \"a later version of .NET is already installed\" and this prevents you from going ahead with Comfigurator installation. If this happens go to Control Panel > programs and features.
Check the box for .NET Framework 3.5 shown below.


.NET 4.8 does not include .NET 3.5
The next version of Comfigurator will fix this problem or give instructions

  windowsFeatures.jpg (Size: 82.88 KB / Downloads: 10) ]]> Comfigurator installation requires .NET 3.5 to be installed, and will prompt for download and installation if it is not found on the PC.

When you try to install the downloaded .NET3.5 you may get a message \"a later version of .NET is already installed\" and this prevents you from going ahead with Comfigurator installation. If this happens go to Control Panel > programs and features.
Check the box for .NET Framework 3.5 shown below.


.NET 4.8 does not include .NET 3.5
The next version of Comfigurator will fix this problem or give instructions

  windowsFeatures.jpg (Size: 82.88 KB / Downloads: 10) ]]> https://www.comfortforums.com/thread-5601.html Thu, 16 Jan 2025 09:25:38 -0500 ]]> https://www.comfortforums.com/thread-5601.html I can graph references to all my other flags but when I try number 1 I get the error shown in this pic.
This is repeatable.
Any ideas?]]> I can graph references to all my other flags but when I try number 1 I get the error shown in this pic.
This is repeatable.
Any ideas?]]> https://www.comfortforums.com/thread-5513.html Sun, 15 Sep 2024 07:28:28 -0400 ]]> https://www.comfortforums.com/thread-5513.html
As an example I have a system with 3 UCMs set with Id 1, 2 and 4. That system works fine of course.Since there are only 3 UCMs, the number of UCMs should not be reported as 4 in Comfigurator.Interesting email alerts will send messages like \"RS485Comms by:  UCM: #3   14/09/2024    20:46:11\" so the system is self aware that there is a UCM #3 even if there no Id3.

Is it possible to fix counting of UCMs in Comfigurator?
I have not thought too much about the implications but if Comfigurator is aware of Name and Type of UCMs, why not make the email alerts more explicit with Id, number, Name, Type. Perhaps something like \"RS485Comms by:  UCM: Id\'4\' #3 Name\'UCM_KNX2\' Type\'KNX2\' date\". Honestly the number #3 does not add much, only the Id is helpful to find the relevant UCM as well as Name and Type of course.

Screenshots are attached one by one over several posts.Thank you

  controller.png (Size: 111.79 KB / Downloads: 16) ]]>
As an example I have a system with 3 UCMs set with Id 1, 2 and 4. That system works fine of course.Since there are only 3 UCMs, the number of UCMs should not be reported as 4 in Comfigurator.Interesting email alerts will send messages like \"RS485Comms by:  UCM: #3   14/09/2024    20:46:11\" so the system is self aware that there is a UCM #3 even if there no Id3.

Is it possible to fix counting of UCMs in Comfigurator?
I have not thought too much about the implications but if Comfigurator is aware of Name and Type of UCMs, why not make the email alerts more explicit with Id, number, Name, Type. Perhaps something like \"RS485Comms by:  UCM: Id\'4\' #3 Name\'UCM_KNX2\' Type\'KNX2\' date\". Honestly the number #3 does not add much, only the Id is helpful to find the relevant UCM as well as Name and Type of course.

Screenshots are attached one by one over several posts.Thank you

  controller.png (Size: 111.79 KB / Downloads: 16) ]]> https://www.comfortforums.com/thread-5510.html Fri, 16 Aug 2024 22:24:03 -0400 ]]> https://www.comfortforums.com/thread-5510.html ]]> ]]> https://www.comfortforums.com/thread-5504.html Thu, 08 Aug 2024 11:36:39 -0400 ]]> https://www.comfortforums.com/thread-5504.html If you are setting up or diagnosing a system there are multiple things that just do not work first time.
- on many occasions when performing a \'scan for modules\' items get re-name and re-arranged- other times the scan dos not pick up the correct device number on the first pass
Its been like it for years but I just now think everybody that uses comfort just accepts it - surely t can be improved its terrible!]]> If you are setting up or diagnosing a system there are multiple things that just do not work first time.
- on many occasions when performing a \'scan for modules\' items get re-name and re-arranged- other times the scan dos not pick up the correct device number on the first pass
Its been like it for years but I just now think everybody that uses comfort just accepts it - surely t can be improved its terrible!]]> https://www.comfortforums.com/thread-5503.html Thu, 08 Aug 2024 11:31:02 -0400 ]]> https://www.comfortforums.com/thread-5503.html Particularly annoying when you log in or do a scan there i absolutely NO indication that the software s STILL performing the task - what happened to the mouse arrow turning into a whirling circle while n operation is still in progress ?]]> Particularly annoying when you log in or do a scan there i absolutely NO indication that the software s STILL performing the task - what happened to the mouse arrow turning into a whirling circle while n operation is still in progress ?]]> https://www.comfortforums.com/thread-5473.html Thu, 08 Feb 2024 20:58:05 -0500 ]]> https://www.comfortforums.com/thread-5473.html http://www.comfortforums.com/forum113/5470.html
]]> http://www.comfortforums.com/forum113/5470.html
]]> https://www.comfortforums.com/thread-5448.html Sun, 22 Oct 2023 01:19:01 -0400 ]]> https://www.comfortforums.com/thread-5448.html Comfigurator 3.14.1 Changes from 3.13.9
Known Bugs

1. Upgrade firmware for Controller shows \"Cannot Obtain Firmware Information\". Workaround -  Please download firmware directly from https://www.cytech.biz/firmware.html Or downgrade to 3.13.9 at https://www.cytech.biz/download_files.php?item_id=1301
2. Upgrading KP04, KP06, IRIO, MSM, TSM by Coimfigurator will case an error \"Incompatible File System\" to be displayed. Revert to 3.13.9 as workaround
3. The number of IRIO Modules are not correctly detected after scan for modules for CM9001-EMS and CM9001-EMS2
4. For UCM/KNX and KNX/Logic in KNX Monitor Mode, when logged in by eth03 in CM9001  telegrams do not appear in KNX Monitor or Learn Mode

Bugs Fixed

1. For CM9001-EMS, No of slaves was limited to 3, now it can be increased to 5
2. For CM9001-EX, No of slaves was limited to 3. Now it can be increased to 5
   
3. The action Set Virtual Input On/Off could not select Virtual Inputs correctly
4. When UCM ID1 is not connected, and Comfigurator is connected to UCM > ID2,  Scan for Modules may show an extra UCM ID1 with firmware version 255.255
   

New Features and Improvements

1. For the Register Monitor in Comfort Register, the right Pane Set Value box does not show the value of the register, so that if the value is constantly being updated, entering a new value will not be affected by the read values. The centre pane will show the register values that are updated constantly
2. Supports Future UCM ARM processor models
   

]]> Comfigurator 3.14.1 Changes from 3.13.9
Known Bugs

1. Upgrade firmware for Controller shows \"Cannot Obtain Firmware Information\". Workaround -  Please download firmware directly from https://www.cytech.biz/firmware.html Or downgrade to 3.13.9 at https://www.cytech.biz/download_files.php?item_id=1301
2. Upgrading KP04, KP06, IRIO, MSM, TSM by Coimfigurator will case an error \"Incompatible File System\" to be displayed. Revert to 3.13.9 as workaround
3. The number of IRIO Modules are not correctly detected after scan for modules for CM9001-EMS and CM9001-EMS2
4. For UCM/KNX and KNX/Logic in KNX Monitor Mode, when logged in by eth03 in CM9001  telegrams do not appear in KNX Monitor or Learn Mode

Bugs Fixed

1. For CM9001-EMS, No of slaves was limited to 3, now it can be increased to 5
2. For CM9001-EX, No of slaves was limited to 3. Now it can be increased to 5
   
3. The action Set Virtual Input On/Off could not select Virtual Inputs correctly
4. When UCM ID1 is not connected, and Comfigurator is connected to UCM > ID2,  Scan for Modules may show an extra UCM ID1 with firmware version 255.255
   

New Features and Improvements

1. For the Register Monitor in Comfort Register, the right Pane Set Value box does not show the value of the register, so that if the value is constantly being updated, entering a new value will not be affected by the read values. The centre pane will show the register values that are updated constantly
2. Supports Future UCM ARM processor models
   

]]> https://www.comfortforums.com/thread-5435.html Sat, 05 Aug 2023 21:57:03 -0400 ]]> https://www.comfortforums.com/thread-5435.html

  UCMSna.jpg (Size: 96.44 KB / Downloads: 7) ]]>

  UCMSna.jpg (Size: 96.44 KB / Downloads: 7) ]]> https://www.comfortforums.com/thread-5339.html Tue, 09 Nov 2021 02:05:55 -0500 ]]> https://www.comfortforums.com/thread-5339.html https://www.comfortforums.com/thread-5335.html Mon, 04 Oct 2021 06:45:33 -0400 ]]> https://www.comfortforums.com/thread-5335.html https://www.comfortforums.com/thread-5329.html Wed, 01 Sep 2021 04:26:06 -0400 ]]> https://www.comfortforums.com/thread-5329.html

If Counter Counter001 = 3 And Flag Flag002 = 0 Then
    Pulse Output001(1) For 10
End If 


After Edit action Codes, the Response will be changed to the below 
 
Get Counter Counter001(1)
BranchIfNotEqual 8 3
Get Flag Flag002(2)
BranchIfNonZero 3
Pulse Output001(1) For 10 

Do not worry, the Function of the Response is not changed, because the action codes remain unchanged, ie
 

81,1, 146,8,3, 132,2,2, 115,3, 130,10,1, 255

The reason for this is to allow Read  fron Comfort - Responses are not changed by Comfigurator. ie the raw Action Codes are not changed by a Read from Comfort so that the working of the Response is unchanged.
Read from Comfort has the same effect on Response has Edot Action Codes

]]>

If Counter Counter001 = 3 And Flag Flag002 = 0 Then
    Pulse Output001(1) For 10
End If 


After Edit action Codes, the Response will be changed to the below 
 
Get Counter Counter001(1)
BranchIfNotEqual 8 3
Get Flag Flag002(2)
BranchIfNonZero 3
Pulse Output001(1) For 10 

Do not worry, the Function of the Response is not changed, because the action codes remain unchanged, ie
 

81,1, 146,8,3, 132,2,2, 115,3, 130,10,1, 255

The reason for this is to allow Read  fron Comfort - Responses are not changed by Comfigurator. ie the raw Action Codes are not changed by a Read from Comfort so that the working of the Response is unchanged.
Read from Comfort has the same effect on Response has Edot Action Codes

]]> https://www.comfortforums.com/thread-5303.html Mon, 19 Apr 2021 06:22:28 -0400 ]]> https://www.comfortforums.com/thread-5303.html Until this is assessed further by Cytech I would strongly recommend that partial download function is NOT used !

]]> Until this is assessed further by Cytech I would strongly recommend that partial download function is NOT used !

]]>