Fibaro Dimmer 2 FGD-212 learned as a Multilevel Sensor

[muddymickey]

[user=5404]bagushandhoko[/user] wrote:

Hi Muddymickey .. its good news for me that you could control FGD 212 from comfort ... have you changed the security association method when connect to aeotec ?

Um, no I don\'t think I did - haven\'t changed any security settings on the FGD-212. I just included it as a non-secure device via Domoticz.

All I know is that from the buttons in Comfigurator I can switch on and off. Not sure if I\'ll be able to send dimming commands or not yet. Maybe this is due to my Z-Wave firmware ?

Just for info I\'m not a pro with Comfort, just a selfbuilder who likes tinkering, so am still figuring stuff out

[muddymickey]

[user=73]leonchue[/user] wrote:

muddymickey wrote:

However, the only Z-Wave command I can choose in a response is a \"Basic Get Command\".  
Any suggestions ?

Have you try to click on the \"Basic Get Command\" and reveal a drop-down arrow?  
Click on the arrow to see \"Basic Set Command\" in the list.

See example as attached.

I\'m 90% sure I tried that. But I\'ll have another look tonight just to be sure.

[tech07]

I have two UCMs: Z-Wave (firmware 7.013) USB (firmware 5.178)

How do I upgrade my USB UCM ?

You need another UCM to upgrade the UCM 5.178 using the programming cableThe programming cable can be used to upgrade another device but not itself
I suggest you ask the supplier of your comfort to do the upgrade for you by sending them the UCM or making a trip to their office

Also - not sure if this is related or not - but since doing this work yesterday, my keypad is constantly showing \"UCM3 communication failure\". 

That means you have 3 UCMs in the configuration but the 3rd UCM is not connected
[font=\"Verdana, sans-serif\"]Do a Scan for Modules and look at the result and write to Comfort again[/font]

[muddymickey]

Can I somehow use the Z-wave UCM to upgrade my USB UCM ?
Swap the daughterboards around or something like that ?

[muddymickey]

[user=2250]tech07[/user] wrote:

[font=\"Verdana, sans-serif\"]Do a Scan for Modules and look at the result and write to Comfort again[/font]

OK, will give that a go tonight, thanks.

[slychiu]

I\'m afraid that doesn\'t work

[muddymickey]

[user=1]slychiu[/user] wrote:

I\'m afraid that doesn\'t work

What doesn\'t - the daughterboard switching ?

[slychiu]

Switching daughter boards makes both ucms nonfunctional
You need another General ucm to upgrade a general ucm via the programming cable
Once the ucm is upgraded to v7 it can upgrade its own firmware as well as other devices without needing the cable

[muddymickey]

Looks like I misunderstood.
When one refers to say, UCM/USB having firmware 5.178 - is this the firmware on the UCM06 motherboard, or the firmware of the USB daughterboard ?

So, given the parts I have, there is no way I can update the UCM firmware myself ?

[muddymickey]

Could I do this:
1) Buy an ETH03 daughterboard, and temporarily fit in in place of the Z-Wave daughterboard
2) Use it to update the UCM/USB firmware with the cable
3) Refit the Z-Wave daughterboard
4) Remove the USB daughterboard and fit the ETH03 daughterboard

So I end up with:
1 x UCM/Z-Wave
1 x UCM/ETH03

Or have I completely missed the point
I\'m half considering an ethernet interface, so wondered if this could be a cost-effective route to it.