A really daft question, and I apologise for the memory block, but I just cannot find this! In my log, at 2300 every night I have a line \'Custom Event 22\' and then at 0600 the next morning, a line \'Custom Event 23\'. What are these and where do I find them? They are definitely not responses 22 and 23! Thank you so much for any assistance......

Just checking on the \"32 Counters\" statement for firmware 8.013. Does that mean only the first 32 Counter values are saved on reset? (Counters 0 - 31)
I suppose for Flags it\'s 254 rather (Flags 1-254) and not 256.
Ingo

Version 8.001
Bugs

1. BUG  from 17/4/24 7.230  alarm type dial index always announce 0,0,0,0 on keypad
   
2. For Ultra - EEPROM locations are incorrect for Time programs,   sunset response sunrise response,  doorphone response, HVAC
   
3. Transfer > Upgrade Sentences fails at LCD keypad words (No Bug for Arm Version)
   
4. From firmware 7.198 - If UCM/knx, UCM/CBus, UCM/Modbus has address   mapped to Flag, Comfort broadcasts the flag to all UCMs but the source  ID of the UCM changing the flag is not sent correctly by Comfort. This  may cause the UCM to send an extra unneccesary message back to the  external Interface for KNX, CBus, Modbus etc. This does not cause the  UCM not to work , it just causes an extra message to be sent back to the  Interface
   
5. Battery check F3,1 when battery disconnected is delayed by 10 seconds and some times does not work from 7.22
   
6. Battery disconnected does not work when there is no battery
   
7. u?82 and higher causes system reset for ULTRA
   
8. For ARM only, virtual inputs do not work correctly. When they are activated, they will reset to the state of the physical input
   
9. \"enter new code and # key\" is anounced  for change/add user code on keypad after entering new code 2 times, but new code is actually accepted. bug for Toshiba only not ARM
   

•  fixed BUG OPTIMUM Only  - F2 home control cause wrong announcement
  
• Fixed bug from V7.255 engineer  menu 6789 7,43, announce firmware announce was blank
  
• Fixed  bug ULTRA CMS Format  was at wrong address so cms could not dial out
   
  

Hi Mr Chiu,
I have programmed my zones 25 to 30 to bypass zone using SwitchNO response. They have been working fine for the last 2 years or so. However, last 2 or 3 weeks I realized that bypass switches are no longer working. Now, the system announces these zones as \"zone Trouble\". As a result, I cannot arm the system. Appreciate your support.

It\'s a minor issue but there is no consistency of numbering between UCM Id (set by dip-switch) and their order in the chain #.

As an example I have a system with 3 UCMs set with Id 1, 2 and 4. That system works fine of course.Since there are only 3 UCMs, the number of UCMs should not be reported as 4 in Comfigurator.Interesting email alerts will send messages like \"RS485Comms by:  UCM: #3   14/09/2024    20:46:11\" so the system is self aware that there is a UCM #3 even if there no Id3.

Is it possible to fix counting of UCMs in Comfigurator?
I have not thought too much about the implications but if Comfigurator is aware of Name and Type of UCMs, why not make the email alerts more explicit with Id, number, Name, Type. Perhaps something like \"RS485Comms by:  UCM: Id\'4\' #3 Name\'UCM_KNX2\' Type\'KNX2\' date\". Honestly the number #3 does not add much, only the Id is helpful to find the relevant UCM as well as Name and Type of course.

Screenshots are attached one by one over several posts.Thank you

Attached Files

Thumbnail(s)
   

I have an input connected to a ISM07 submodule that I have configured as RIO Input and have setup on/off responses  (SCS/RIO).

I have a need to use this input as an alarm input, and I cannot physically wire this, so I thought of using one of the alarm inputs as a virtual input.

What would be the ideal way of doing this?

1.  Change the input from RIO Input to Virtual Input on the ISM07? Would I still need to flag the alarm input as virtual?
2. Add actions (Virtual Input on and off) to the existing responses and set the flag of the alarm input as virtual?

• Comfort Model: CM9001-ULT
• Comfort Version 8.005
• ScsRio (IRIO) Version 7.024

Hi All,  

I decided to take the great work done by @koochyrat and others and update the scripts to integrate a bit more with Home Assistant.
https://github.com/djagerif/comfort2mqtt 

A quick disclaimer: I am not a programmer, I tinker a lot, so please don\'t be too critical of this HA Addon. I do have a day job so time, and skill, to figure things out and trying to make it work is limited.
Feel free to test and comment and if there is something that is broken, and I am able to fix it, then I will give it my best shot.
Development was done on an old CM9000-ULT with a Cbus integration. Anything else is a best-effort bonus that I can\'t test or develop for.
The documentation is extensive, I tried to put EVERYTHING in there so if you don\'t understand something, please read the docs again, it should be in there somewhere.
You will need to configure your own flags, sensors, counters, zones etc. I only programmed a few system objects as a start.
Ingo

Attached Files

Thumbnail(s)
   

The images that you have posted in all your messages today cannot bve seen!

Occupancy Status in Comfigurator
see http://www.comfortforums.com/view_topic.php?id=5158&forum_id=20&highlight=occupancy

Occupancy Status in Comfigurator
see http://www.comfortforums.com/view_topic.php?id=5158&forum_id=20&highlight=occupancy