If you still want to use Comfigurator 2 with Comfort v7 firmware, the last firmware version which can be used is version 6.007 (in 2001). Up to this firmware version, the Engineer User number is 18. after this version the engineer user number was changed to 254. This was done so as to allow more Users (eg CM9001-EX) has 99 users.

Comfigurator 2 expects Engineer user number to be 18, and you need the engineer code sign in to write and read to Comfort.Hence Comfigurator 2 will not allowe write and read to Comfort Firmware > 6.007 Comfigurator 3 does not require engineer code sign in

It is highly recommended to change to Comfigurator 3 wjhich can co-exist wioth Comfigurator 2 in the same PC

I have Comfort Mother Board number A017826 (it has it\'s other half C097167) This board has the 8 output sub board plugged into it, with an 8 pin chip ULN2803A soldered onto it.
3 of the outputs have stopped working, so I can only assume the output IC has failed on this sub board?
Can you tell me if  this plug in sub board can be ordered as a replacement and what is the official description of the module? I would have a go at replacing the 8 pin IC, but there are several other components very close to it
Many thanks  Graham

Attached Files

Thumbnail(s)
   

see http://www.comfortforums.com/forum113/5470.html

see http://www.comfortforums.com/forum113/5470.html

see http://www.comfortforums.com/forum113/5470.html

To access comfort remotely by dynamic DNS, you need to have an account with a service like no-ip or dyndns.org . This may not be free but you get a number of addresses that you can use eg user.ddns.net 

Your router should support the ddns service. You will get a user name and password to log in to the service. As an example, see below




Other routers will have different menus to set this up.
Next, set up Port Forwarding on the router as shown in the example below. You need to map the internet Port to the Local IP Address and Port



Again, different routers will have different menus to set this up.  When this is done you can use the dynamic IP address eg user.ddns.net as the remote IP address in Comfigurator or the Cytech Mobile app

Hi,

I have an install with a 9000 Comfort 2 panel with firmware - Week, 5.045, file system 34 and UCM type 10 v 5.092 (old serial UCM). X10 is also in use in this install, so no option for a 9001 upgrade

It\'s using the last version of Comfigurator 2 (v 2.2.3) and whilst the upgrade to Comfigurator 3 is on the to do list (as is updating to a UCM6/ETH), that won\'t happen yet but it will be good to be able to nevertheless update the Comfort and UCM firmware to the latest version.

Are there any restrictions to what version of both Comfort and UCM Serial to upgrade to whilst maintaining compatibility for the current Comfigurator 2 (CCL) file?

Hi,

Old KT01 here again . I\'m determined to keep this thing alive!

I\'ve managed to update it for an irrigation upgrade, added an additional irrigation zone and some additional action buttons, all working well.

However, both before the upgrade and now, I can\'t hear any announcements from the KT01 panel itself eg announcing irrigation zone status, although I can hear them on the one other KT04 keypad on the first floor. Key press beeps are perfectly audible, so I don\'t think its a speaker issue.

All voice and mic connections are sound.

Any ideas?


PS Although audible on the KT04, announcements are somewhat muffled, maybe a speaker issue but perhaps worth noting.

see http://www.comfortforums.com/view_topic....rum_id=126

http://www.comfortforums.com/forum4/1782.html 
Hi I\'m trying to reflash a UCM/Ethernet after an Unsuccessful  Firmware upgrade :-( 
All goes well until I load the Firmware [color=\"#004080\"][font=\"Verdana, sans-serif\"]UCM7_176.cbf file [/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]
[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]and it comes straight back with [/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]
[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]Error reading Config\\sboot.cdf: Could not find the file \'CProgram Files [/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"](x86) Cytech\\Config\\sboot.cbf\'.[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]
[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]
[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]And its right it\'s not there so it terminates.[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]
[/font][/color][color=\"#004080\"][font=\"Verdana, sans-serif\"]Mike[/font][/color]