Hi,Currently my comfort alarm has a direct connection to my home telephone line.We have just been informed that BT in the UK is changing this line to digital.How will this affect my alarm or is there something i can add to the alarm to make it digital computableThanks for your help..

Hello,
For several days I have encountered a problem. I no longer receive text messages. If I still send an arming order by SMS, nothing happens. I presice that my system is working perfectly through the application.
So I am going back to comfigurator. I updated the whole installation but still nothing. I also tried with a second sim card. In the status bar it appears \"Unknown GSM Module\".

Can you help me solve my problem?

Regards

This video shpws the Comfort App Arming to Away Mode when connected Remotely.

https://www.youtube.com/watch?v=88BIcEHDnM4
This shows how you can arm the security system from outside the house, and can froce arm if zones are open.You do not need to exit the premises when connected by Remote

The sequence is as follows

1. Connect by Remote
   
2. System is disarmed
3. Press Away Arm
   
4. There are open zones which are displayed
5. Press Force arm to automatic bypass the open zones
6. system arms to away mode. No need to exit when connect by remote
7. system is arnmed tio away mode
8. Movement causes intruder alarm
9. Enter code to disarm

The firmware 7.194 has this feature:

If IDBUTTON is pressed and held at reset, disable Responses This allows system to work even when there are responses with endless loop, ie Responses calling themselves, ir problems in the Startup Response.
Another method is to press and Hold the DLOAD Button in the UCM for 2 seconds which until the BUSY2 LED starts blinking. See http://www.comfortforums.com/forum4/3419.html

Firmware 7.194 has a new feature:
see http://www.comfortforums.com/forum79/5258.html

As a reminder, when the door station button is pressed, pressing any button on a keypad will activate the Keypad to Door station 2 way intercom.

For the new feature, during Keypad to Door station Intercom mode, pressing and holding any keypad button will cause keypad to door station to be 1 way, ie Keypad can talk to door station, but Door station cannot talk to keypad.When the keypad key is released, normal 2 way intercom mode is activated.
This may be useful when there is noise outside on the door station side. One way mode is normally louder than 2 way mode. This also helps to check whether the intercom is working

I am still running V1 (I know, but it\'s not broken and getting an upgrade in the UK was tricky).  I have just used DS Manager to change the IP Address of my Ethernet UCM as I have just changed to FTTP (which, by the way, is very nice!).  I did poke most of the buttons on the Ethernet UCM before I got it to talk to DS Manager.
Unfortunately, since then, it seems that contact with the CBUS UCM has been lost - there is no comms between Comfort and CBUS.  To try and resolve that I reloaded the latest CCL file (using Comfigurator 2.2.3), with no difference.
I have tried resetting the CBUS UCM and, again, no difference.
So, basically, I am looking for some inspiration on what to try next.
Here\'s hoping!
Thanks,
Nick

I recal that the SCS switches were going to be replaced and as such that doesnt seem to have happend is their an alternative that I could use as customer was hoping for SCS06 switches as I demonstrated them in my place.

Unfortunately the CAT5 terminator which connects into the rear of the KT03 has been lost. Is this a standard connector ? How can I get hold of another ?

Thanks

Steve

I have a replacement laptop that has the same OS Build as my old laptop (19043.1165), but on the replacement laptop I get an error when I try to enable Framework 3.5 (Error code 0x8024401C). With this I cannot install Comfigurator.

Hi,
I bought a Comfort system many years ago but for various reasons I am only getting to install it now. I apologize in advance if my question is answered somewhere on the forum but cannot find any recent posts on this topic.
I understand Comfort can interface with many 4rd party systems such as ZWave, KNX, C-Bus etc., but devices for these systems seem very expensive compared to the zigbee, Tuya Smart type devices currently available.
Does Comfort have a UCM or other capability to interface with such devices? I see that back in 2006 there was some focus on the UCM/Pi but have things moved on since then?
Thanks,Paul
PS: thanks to the Comfort team and the many forum users because its been very helpful as I installed my system.