Bugs Fixes

1. Copy ID could not set ID to 5
2. Slave zone analog value was not correct Not affect 7.117
   
3. Strobe did not work on slave
4. Fixed Intermittent Communications Failure which may occur every day or every few days, applicable for Slave PCB hardware without Zone EOL shunts
   

Hi all,

I am sharing my Comfort integration with Home Assistant. This is a standalone Comfort to MQTT bridge for Cytech\'s Comfort II Ultra Alarm system with UCM/ETH03 module primarily intended to integrate with Home Assistant (or OpenHAB or other MQTT compatible systems). It can run on a Raspberry Pi and other systems with Python 3 support.

With Home Assistant, you can further extend the Comfort system with more complex logic, inputs, outputs and actions. Using virtual inputs, you can define additional zones in Comfort triggered by any sensor available in your Home Assistant setup. Or vice-versa, having Comfort trigger any action in your Home Assistant setup.


Instructions and source code available at:
https://github.com/koochyrat/comfort2

Attached is my HADashboard setup for Home Assistant

Hi,
Did anyone try to integrate Comfort to the Leviton Bitwise controller yet.
Would like to offer that to a clients with integrated automation system.
(C-bus, Comfort)

Looks like we need Java script files from Cytech though.
Any ideas.

Thank you.
Brodsky.

Hi can anyone suggest a method of using Comfort as a watchdog?I have an \'alive\' message coming into my UCM at regular intervals and I would like to trigger an alarm or warning if the messages stop arriving.

Bugs Fixed

1. Fixed Potential Intermittent Communications failure that may occur every day or every few days, especially if the Comfort PCB hardware does not have Zone EOL shunts
   
2. Fixed Bug s! To ETH03 on CM9001or UCMLOG  does not update sensor to rs485.
3. Fixed BUG f?00 On eth03 on CM9001 or UCMLOGreturns wrong flags states
4. Fixed bug in UCMLOG no of slaves reply was wrong for Y? Reply. Now  z? Will get dummy reply instead of no reply
5. Fixed BUG is Tamper Nondetector alarm is null and Tamper is open, arming cannot complete, keeps announcing Please exit and no zones announced.
6. Fixed BUG phone Voice menu did not select the correct  partition for user when signed in

1. Action change entry time works if system is armed but not if it is 24 hour zone. Now it works for 24 hour zone even if system is not armed
2. For GSM, After receiving (4xxx) sms, if there is no feedback in the control menu, dont send \"Invalid Command\" to SMS. Bug from  7.077
3. Each partition will resend sms for open zones when in alarm state according to the interval in minutes in Alarms >  Misc Settings> SMS Repeat Time (Needs new Comfigurator 3.12.6). The SMS will be repeated after every interval for the zones that are still open until the alarm times out. If the SMS Repeat time is 0, then the sms is not repeated
4. GSM SMS  SMS user number 240, 241, 245 etc will not send  user number 240, 241, 245 and dont send \"User\" Instead  \"Keypad, By Response, SMS\"
5. After writing to Comfort after  a file system mismatch, ie EEPROM file system mismatch with the Firm ware and the correct File was written to it, fixed problem where Comfort does not reset automatically, and needed to press the reset button
6. For Control Menu, activate action key eg 0 or 1 remove check for control action word is non-empty so in case vocab mismatches the comfort app still works
7. Changes in  the internal polling algorithm
   
8. Configuration Flags added GSM Priority When checked, system will dial out by GSM as pririty instead of fiuxed phone line even when the fixed line is installed. Requires Comfigurator 3.12.4
   

Help! I\'m having problems with control functions from the iOS app.

Using Comfigurator - V3.12.3.0 and iOS App v1.3.1 (34) - System running 7.117 and Eth UCM running 7.098.

Download latest config successful to system and it resets... put the CCLX file through the conversation tool, open it on the iPhone and import into the iOS Comfort app.

I can log into the app, change security mode and it reports correct variables (e.g. zones open etc) however control features simply wont work... any ideas?

Cheers

Simon

I\'m after confirmation that this is the right approach. I stopped updating the firmwares some time ago as it was cumbersome to say the least with cables. I have :

Comfort II Ultra  6.011 (has the daughterboard CPU)
UCM 10   6.002
CBUS UCM   5.217
Universal UCM  6.003

Am I right in thinking I should:
1. With the cable from one of the UCMs, upgrade the Ultra firmware firs
t2. With the cable from one of the UCMs, upgrade the other UCMs
3. Put the cable into one of the recently updated UCMs and update the last UCM.
Does that sound about right?
Thanks

Evening all
In the last month or so I have experienced comfort zones randomly freezing. IE. Sticking in a particular state.
It can be a single zone or multiple zones.
A refresh of the zone from the SmartThings app does not recover it, but mostly a Bypass On followed by a Bypass Off normally brings it back to life.
Any idea how I can troubleshoot this in more detail to find out where the breakdown in communication is happening?
I tried to download logs from the alpha-uhai page, but it downloads a 0 byte file.
Hoping for some help
Thanks Jim

 Hello Everyone.I am here to introduce myself.Life is all about living on your own rules and regulation but when it comes to forum you have to follow the rules of forum because if you dont follow admin will unfollow you. Waiting for someone to welcome me.

Regards,Shizu     













































Sir MVIT admissionMVJ College of Engineering  AdmissionSir M Visvesvaraya Institute of Technology admissionMVJ Medical College admissionRV College of Engineering Management Quota Admission              

There might be a very obvious answer to this but I have missed it...
One can use the Fn+key to select a function on the keypad e.g. Fn+2 = home control yet if you log in or use the voice menu remotely, different key combinations apply e.g. \"select 4 for Home Control\".
Why are the key/function binding NOT the same on both the keypad and voice menu?
I believe I can reassign the keypad key/function binding with Comfigurator but the keypad icons will no longer then be relevant.
I can\'t think of anyway to change the voice menu assignments.
Is there any good reason for this difference for those of us with OCD tendency ?