I am looking at the QMotion blinds which have a Zigbee control option.
Has anyone successfully interfaced Comfort with Zigbee and these blinds in particular? 

Can I ask for some help please? - I thought I would try using partitions. I have set up a new SEM, dedicated for a takeaway, which is part of my main office. I looked at all the info on the forum and it seems you can mix the old KPO4 , which will remain as and behave as partition 0.I have installed a new KPO4A in the takeaway and called it partition 1 and assigned door switches and smoke/heat detectors to partition, 1 Leaving all the 4 office KPO4’s in circuit. Now, as soon as I upload the configuration and Comfort resets itself at the end, the system goes into Night Mode. If I change all the zones back to partition 0 the problem of auto Night Mode goes.So,with only user names and the one KPO4A assigned to partition 1 there is not a problem.CAN you mix new KPO4A’s and old KPO4’s on the system, or should I be looking at other things which are causing it to  reset straight into Night Mode, when I change the takeaway zones to partition 1?

If I use Eth03 with a Comfort 1 and the latest version of Comfigurator .........
- Will the sunset / sunrise times be operational if i set Lat and Long? e.g. in miscelaneous events will the sunrise and sunset response work?- Can I set the internet time to update the internal time clock ?

Numeric Values of Communications Failures according to IDs

• 17 to 25: UCM #1 to 8
  
• 33 to 37: Slaves #1 to #5
• 49 to 51: Door Station #1 to #3
• 65 to 79: Keypad #1 to #15
• 81 to 95: IRIO/SCS/RIO #1 to #15
• 113 to 127: Sensor Module (TSM or MEM) #1 to #15
• 129 to 154: HIO (Hotel IO) #1 to #15
  

I\'m not sure what has happened but during my updates and reprogramming I have lost my Vocabulary, I have tried updating using Myma39 in an attempt to rectify this but I get the beeps on the keypad and then I get a vocab errors message. Can you advise on how I fix this.

Attached Files

Thumbnail(s)
   

Using Comfort as a KNX interface or indeed using the KNX logic module, I think that moving forward it is going to be essential that Comfort becomes a recognised KNX partner.
Comfort need to part of the KNX project file device list.
When programming in KNX tracing the source of where things come from and go to is essential. 
So taking a basic example of using Comfort (internet) time. Setting this up from the Comfort side is easy it simply requires a KNX group address to be input into event 33 and 34 of the KNX UCM schedule.
HOWEVER looking from the KNX ETS program side there is no way of telling that the Comfort telegram is being used (apart from ..... (1) monitoring the address (2) using a dummy KNX device (Ive called it Comfort alarm and got it grom the GIRA device list).

I have ETH03 set up to synchronise comfort time.
Firstly how can i tell that i\'m using comfort time or synchronised time?
Secondly I want to be able to use the comfort (syncronised) time for KNX time? Cannot see a way of sucking date and time out of comfort?

Hi,
Having trouble arming the system and getting confusing messages about what is causing the problem.
We have a fairly common set up of Exit Door as final arm (wired magnetic contact set as EntryDoor) on zone 17 and the area is covered by a wired PIR as well (AlertAway) on Zone 7.
The last few times we\'ve tried to arm it has failed.  The event log gives the following:

• 04/20 12:08 Sign in - User # 1
• 04/20 12:08 Mode Change # Security Off
• 04/20 12:10 Restore - Zone # HallMotion (7)
• 04/20 12:10 Restore - Zone # HallMotion (7)
• 04/20 12:10 Custom Event # 12
• 04/20 12:10 Alarm Type # ArmFail (4)
• 04/20 12:11 Sign in - User # 1
• 04/20 12:11 Alarm Type # AlarmAbort (20)
• 04/20 12:11 Sign in - User # 1
• 04/20 12:11 Mode Change # Security Off

After several years of the system running well I decided to add some more functions and installed a ucm z-wave. I was able to connect to everything using configurator.
I then did the firmware upgrades and I thought all was fine. I went back to the system a couple of hours later and it appears that ucm eth02 is not connecting to the network. If I run the dsmanager on the network nothing Is found but if I plug the module directly to my laptop I can see the UCM and set the IP or dhcp.
When plugged into the lan the device does not show up in the list of connected devices on my router list.
Can anyone help me trouble shoot this?

HI I have a Raspberry PI that I set up using Noobs a week ago, how do I now use this to install this package? I have formatted the SD card and written the image but I can\'g get past the multi colour boot screen.
Do i need to do anything to remove the current configuration before this will work?