We have an existing installation that we have recently upgraded for the customer. The set up was using a UCM with an RS232 daughter board to connect to a centralite system.
After upgrading the UCM to 7.XX there appears to be no communication out of the UCM.
When an RS232 communication is sent...- There is a flashing LED on the main board L10 L11 - NO flashing LED on the UCM D9 and D10
Am I correct in saying that the LED\'s D9 and D10 should flash when an RS232 communication is sent? 

I have just set up a new Comfort unit supplied with a 14V DC transformer.
The customer has a door phone that requires me to fit a ringer module (RGR05).
The RGR05 is clearly marked 14VAC.

When is a replacement RGR(06) unit available that can handle the new DC input?

I use confort since 2003, being the automation made by X10. I currently have 2 AD10 modules broken, but I\'m trying to replace them with Sonoff modules or (Shelly 1).
I also have a CM15Pro module that uses Active Home Vista 2.5.5 application on my PC.
My question is how to send X10 commands to command these modules.
In other words, I need an application that receives for example the order

-> (A8 On) coming from Comfort

and create a web command that sends to Sonoff module via IFTTT

-> https://maker.ifttt.com/trigger/A8_on/wi...YIZL0GzIhN

JG

I have just fitted two KP05A keypads for a customer, When I openend the keypad, there are no jumpers to select ID, when I read the manual it keeps refering to jumper settings for the keypad, The manual is out of date and there is no explanation how I am  too change the ID on the keypad.Can you tell me where the correct installation manual is for this with directions on setting the ID

https://www.cytech.biz/kp05a_keypad_lcd_horizontal.html

Hi - I am having problems with z-wave. I have a Z-Wave 3.42 version 7.104. My Comfort is Comfort 2Z Ultra version 7.142.
I noticed yesterday that a virtual device was not working as it should. I now realise this could have been happening for some time! When I looked at the device it had changed from virtual to basic. I have recently added some new z-wave devices to the primary controller, Homeseer using a zme_uzb stick. All the devices controlled by HomeSeer are working as they should showing no errors. I thought doing a Learn might resolve the problem. I did the Learn and the device that was showing basic reverted to virtual and the new devices appeared in the list. I wrote to the EEPROM when Comfigurator asked me to do so.
However, I then noted a different device although showing as virtual was not in green text and was not working as it should. I did another Learn.  This appeared to work but when Comfigurator asked to write to the EEPROM I got the message; The EEPROM data is invalid - please perform a Learn Z-Wave Network operation. I tried to do another Learn but nothing happened. HomeSeer tried numerous times to send the info then timed out. The Comfigurator popup appears; Waiting for response from Z-Wave. It just sits there and does nothing.
I have tried this several times to no avail. I also tried locating the usbstick on the primary controller nearer the Comfort z-wave aerial but that made no difference. This morning I tried to Read From EEPROM and got the same error; The EEPROM data is invalid - please perform a Learn Z-Wave Network operation. I tried a Learn again but still to no avail.
I now am in the position that I can\'t read or write from/to the EEPROM and neither can I Learn from the z-wave network. I have done a reset on the Comfort and restrted the PC running HomeSeer.
I\'m not sure what to try next so all suggestions gratefully received.

Cheers,
Ian

Hi All

Please find below the link to the UCM/Pi Beta Phase 2 application form.

If you are interested, please complete the form and we will be in touch when they are ready to ship (expected end of March 2019).

https://goo.gl/forms/YgICZH2fyMzwmTyw2

Thanks,

Matt

One of my Zones, and external door, creates a \"Zone Trouble\" alarm when the door is opened, even though the Security System is un-armed.
I can arm the system even if this alarm was previously triggered.
Why is that, what does it mean, and how can I fix the issue - whatever it is.

Zone input 17 has got the virtual input checked, I have made some changes to the config recently to shunt this zone via an RS485 message but now the zone doesn\'t detect anymore. 

Attached Files

  96 active.cclx (Size: 272.39 KB / Downloads: 2)

I\'m having problems with getting feedback from the UCM_KNX2.

KNX -> Comfort...
0/4/7 (1-Bit) \'Blind up/down\' mapped to Counter031

Counter031 response...[indent]If LastUcmCounter = 0 Then[/indent][indent]Do BlindUp[/indent][indent]Else[/indent][indent]Do BlindDn[/indent][indent]End If[/indent] Counters->KNX (1-Bit)...
Counter031 mapped to 0/4/8 (1-Bit) \'Blind up/down status\'

In this instance (If I understand the UCM manual correctly) GA 0/4/7  should alter the value of counter 031, which should alter the state of GA 0/4/8.
In reality, when Group Address 0/4/7 is set to \'ON\' the blinds come down, and when Group Address 0/4/7 is set to \'OFF\' the blind go up and I can see the counter value change in Comfigurator (Comfort Registers) so this all seems to be correct.
However, the status value DOES NOT change in the status columns of the UCM and I don\'t see any telegrams to Group Address 0/4/8 in the group monitor on ETS, or any other indication that I\'m receiving feedback from the UCM_KNX2.
What am I doing wrong?

HELP! - my main panel has just died... I measure 230V at the transformer, and I measure 16VAC at J102 on the RGR. However in the digital section I measure only 3.6VDC across the 12v+ / 12V- pins. there are no lights on ANY board, nor any of the UCMs attached to it, and all sensors wired to it are dead. I\'ve tried a total power down, but I can\'t get it to show any sign of life... - is it FUBAR?
Any help at all would be much appreciated, as my system seems totally dead at the moment.
TIA (hopefully)
Paul G.