As I understand it the new KNX logic controller will not initially be able to upload or download the ETS program.
IF this function is at all possible in the future it would be exceptionally handy to have as a function of the controller. 

I have been supplied with an SEM01 along with a new 15VDC switch mode power supply (separate purchases !).
Upon booting up i found it did not work. I received a replacement from CBUS shop that did not work! 
Upon closer inspection the SEM pcb has \"DC15V\" imprinted on the pcb. DC being polarity sensitive it also has \"+ve and -ve\". 
It appears that the output of the transformer was wired the wrong way around on the transformer lead.
------------------------------------------------------------------------------------------------
I am assuming that the new switch mode power supply 15V DC output will replace in its entirety the old 14VAC transformer.
Although the new switch mode power supply is ( I believe) backward compatible. The old transformer will NOT then feed the new DC15V pcb ( as it is 14V AC output ).
CAN SOME ONE PLEASE CONFIRM IF THE NEW CPU WILL EVENTUALLY USE THE SAME DC15V CIRCUIT AS THE NEW SEM - IF SO THEN ANY C1 UPGRADE WILL REQUIRE NEW SWITCH MODE POWER SUPPLY TO BE FITTED.

Hi,
I just posted a thread about our UCM/ETH03 not working. Meanwhile we had a UCM/ETH02 ) still on firmware 5.xx) sitting around that we used to use with our comfort 1.
The timing of our system is out of whack hence the urgency to get into the Comfort and set up the schedule again properly.
In Comfigurator I am not able to connect to it. Using DS manager I was able to setup it up and assign it an IP in our home network, and setup gateway of the adsl router, and appropriate subnet mask. This way I can try and connect via my laptop on Wi-Fi internally in the home network.
But if I try and read the schedule or system information I get an error that connection cannot be made to UCM. So looks like DS Manager can connect but Comfigurator cannot. I tried changing tcp/udp, port number but nothing has helped.
Any tips would be much appreciated.. 
Also I understand I can swap the sub-module between UCM/ETH02 AND UCM/ETH03 - the ETH03 module seems damaged but hopefully it\'s UCM board (on firmware 7.xx) is fine.
Thx

Hi,
We bought and setup the original comfort system in 2004. We then upgraded in 2015.
We needed to reprogram some light timings and couldn\'t connect via the UCM/ETH03. We tried to reset it using sw1 and sw2 on the sub-module but nothing is happening. Many other lights on the UCM and ETH03 are on, but the lights on the RJ45 port don\'t light up at all. The D2 light also never switches on.
Here is a quick short 15sec video showing the startup of the card. Any help much appreciated.
[flash=425,344]https://youtu.be/i8_Ylzv/&hl=en&fs=1[/flash]
Some stills:

Possibly this could have been due to a storm we had that knocked out a couple of other electrical items. The other things in the Comfort system seem to be working on though.

Attached Files

Thumbnail(s)
   

KNX/Logic will be a UCM sized Controller with a plug-in KNX Interface.

It will have all the functions of the UCM/KNX2 except that this is not a UCM that is connected to Comfort.  It is a Controller like Comfort, but without Inputs, Outputs, Voice. messages or Alarm Functions. 

It is like the UCM/Logic Controller, except that instead of ETH03 plug in, it supports the KNX Module
It supports all the Comfort RS485 Bus modules, eg UCMs, IRIO, HIO, MSM
It will have Counters, Flags, Sensors, Responses which are used for logic programming and control.
The applications for this product include;

• Low cost Logic Engine for KNX - allows use of Comfort extensive logic conditional features
• Interface between KNX and other modules supported by Comfort , eg C-Bus, Modbus, Velbus, UCM/PI, IRIO, HIO
• Uses - in Hotels, Commercial and Industrial applications.

Hi. Recently upgraded my plastic door station to a metal one DS01.

The sound quality is really poor.

Do I need to upgrade my DM01 to a DM02 also?

Or is it just tuning parameters I need to play with? Could you point out the correct tuning parameters/ which ones to adjust please?

Thanks
Kevin

Do we really need both !
As an installer I say NO absolutely pointless - simplified will never be used !

Need to identify a few tings on a really old SEM Gen1 but can\'t find documents for it. Can anyone point me at them or post them please? Specifically..What is JP12 in the corner and next to the KA/KB and the white 4 pin header? Ta very muchly.

I am upgrading my old Comfort 1 system to Comfort 2 Ultra, but I am having problems with my existing KP01 keypad - Audio from the Keypad is distorted.

The comfort 1 had a pot to adjust the audio level, but the Comfort 2 does not.
- So is the KP01 basically not compatible ? - do I need a KP03 ?

We have a new Comfort CPU 9000 - I note the following updates:
- The 8 outputs are removed from the main pcb and are on a daughter board. Would it not have made more sense to utilise an \'output\' UCM in this way it may have been possible to remotely connect or mount the utput board !
- EOL jumpers are now revoved and appear to work well in software. YES WORKS WELL.
- Tamper is now a three pin fixed to pcb - this is helpful for joining commons BUT its a different type of connector that sticks out of the side of the pcb - will this not cause problems in packaging !
- X10 removed - yep about time its totally redundent you cannot buy the X10 DIN modules now even Insteon replacements are not available.

Is there anything else we should know about!