We have a system set up which is controlled from the clients iphone and we also have access on android.
The android app arms and disarms OK
The iphone app appears to put the alarm into some setting dilemma. basically it will not arm and comes up with the message \"zone 0 error\".
All firmware latest
Any thoughts

Comfigurator 3.12.1 supports the Multiconvert action (But only from Firmware 7.128)

Go to add actions \"Arithmetic \" select Multiconvert





The options under Multi convert are

• Convert C to F
  
• Convert F to C
• Convert (0-255) to (0-99)
  
• Convert (0-99) to (0-255)
• Convert EMS temp to -20 to +80 deg
  

In Comfigurator 3.12.1,  the real time state of Flags, counters, outputs which are mapped to KNX, CBus, HIO can be displayed  directly in the modules and the state can be changed or controlled in the KNX, Cbus, Modbus  module. This is a very useful tool for testing the mapping in both directions

UCM/KNX2
    • KNX to Comfort
    • Outputs to KNX
    • Flags to KNX
    • Sensors to KNX
    • Counter to KNX 1 bit and 1 byte

eg in KNX to Comfort, the mapped flags and Counter status can be seen



The Show status box when checked alows the state of the mapped flag to be seen
Furthermore the state can be changed to on or off



When a KNX group is mapped to Counter, the value of the counter can be seen and changed by selecting the value and entering a new value in the range 0 to 255

Comfigurator 3.12.1  introduces changes to simplify programming. Current users should familiarise themselves to these changes.


Categories
The Categories on the left pane have been rearranged to simplify programming.



For example, the \"Security\" and \"Security Types\" Categories have been combined into \"Alarms\". Everything associated with Alarms are now in this catergory.




\"Comfort Registers\" is a new category which combines screens from \"Events\" and \"Names\". It puts together all the registers ie Counters, Sensors, Flags, Outputs, Timers in one place




\"Events\" is the same except that \"Responses\" is now listed on top as it is most used

Comfigurator 3.12.1 introduces several new View Modes which reveals only the features that are relevant to the application, and hides other features and settings that are not needed. This is because Comfigurator has become quite powerful and complex over the years, and may be confusing to new users.

The Viewing Modes are;

• Engineer Advanced - This is the full view with all features. This is the existing viewing mode
  
• Engineer Simplified - This is a simplified mode which hides seldom used screens and features, applicable to Comfort CM9000
  
• Automation - This hides the alarm related screens and features, applicable to LGX01 Logic Engine and UCM/Logic systems without alarm and voice
  
• EMS (Environmental Monitoring System) - This is for the new Cytech Environmental Monitoring System application
  
• User - This is for users which hides the engineer programming screens. This is an exiting Viewing mode
  

Hi,

I\'ve got an old Comfort I system. The main PCB has a chip labelled “Outside 4.169” A006166.  The slave SEP modules have a chip labelled First 4.164.  The SEP PCB is SM0223.

I\'ve noticed that when arming or disarming the S12V connection on the SEP does not switch off, whereas it does on the main CPU.  I suspect this might have always been happening.  Both SEPs exhibit the same the problem, so I don\'t think it\'s a faulty PCB.

I found in the forum that there may be a jumper that needs removing (J7).  I removed that, pressed the SEP reset button and tried again, but no luck.  Have I got the right jumper?

I know it\'s a very old system but as it\'s functioning perfectly other than this, I\'m reluctant to upgrade it.

Any ideas?

Kind regards,

Tim
 

Hi 
I\'m having a moment after Comfort has kept me awake all night announcing \"Tamper Alarm\" every few seconds even though the system is fine.  In fact having announced all night it has now decided to stop for a while.
Anyway what is the best method to disable the announcement side on the keypad?
I\'m looking in Comfigurator but not immediately obvious to me; not seeing anything on the \"Alarm Types\" section to do this unless I am meant to set the phrase to \"(Unused)\".
Ju

I recently implemented a magnetic door latch, the unlatch command is \"200, 49, 2, 50  255\"
This should give a 2 second activation when I press 7 on the phone but I only get 0.5 second, changing the duration doesn\'t change the unlatch time.
Comfort 2 Ultra, V7.117

It\'s happened a few times in the past but it seems again I am struggling with my old nemesis being the lights seem to go on and off by themselves.
At the moment it is my downstairs hall light that is going on and off by itself every few seconds in what seems like a battle with itself.
All my ZWave is controlled by my Fibraro Home Centre 2 as are all of the light switch dimmer modules.  I\'ve had no problems for the last couple of weeks as I had my Comfort System temporarily off while I did some work in the loft but today on it went again and the problem started up!
I am 100% convinced Comfort logic is broken here somewhere,  I sat in Comfigurator watching the counter toggle from 0 to 255 every few seconds based on incoming responses (from where who knows).  Interesting the problem stopped as soon as Comfort was rebooted only to then resume again.
I watched the counter and noticed the counter sometimes reflected the opposite of what the lights were physically at and I\'m convinced it is falling out of step somehow.
I\'ve just broken out of the cycle (at least for now) by waiting until the counter showed the opposite to the actual light and then switching at the light switch to match; the problem then seems to have stopped.
Maybe just a symptom rather than the actual issue but what is true for sure it that I\'m pointing the finger at the UCM/ZWave right now.  Chiu could we have some sort of monitor (like other UCM\'s have) to aid in the debugging of this sort of issue.  Maybe it is the smart polling that is causing, who knows but my sanity (or wife\'s nagging) is suffering now for sure.
Helpppppppppp!
Ju

Bugs Fixed from 3.11.4

1. Home Control Menu in some view modes did not work
2. Graph References caused exception if a printer is not set up
3. Fixed bugs in View modes
4. IRIO when IR Signal Output was mapped to Counter and changed to Flag, an exception occured
   
5.  In Modbus, if Display mode is Decimal when the file is opened, when you go to the Modbus to comfort, the display is hexadecimal. To show as decimal, you must change the mode to hexadecimal and back to Decimal, then the display is in Decimal.
   

• Re-origanised the display of screens in Comfigurator categories to make it easier to access http://www.comfortforums.com/forum20/4763.html
  
• View Mode: Automation has been added to other view modes (User, Simplified Engineer, Advanced Engineer, EMS). The view mode is now saved in the cclx file. Each default template has a default view mode. see http://www.comfortforums.com/forum20/4763.html
  
• Added Multi-Convert actions (Action code 159) - Convert deg F to C, Deg C to F, Convert (0-99) to (0-255), Convert (0-255) to (0-99). From Firmware 7.128. http://www.comfortforums.com/forum20/4765.html
  
• Added Action Code  Toggle Counter (action) 158. This treats the counter as a binary object. If the counter value is 0, it becomes 255. If the counter value is >0, it becomes 0. From firmware 7.100
• KP04A/KP06A Properties - Tamper is disabled by default. Most users disable Tamper so default disable is more convenient
• Status of Flags, Counters, Outputs can be set, cleared or value changed (for counters) http://www.comfortforums.com/forum20/4764.html