Has anyone heard if the new UCM interface with Alexa and other voice control devices  is anywhere near completion? I have 2 jobs pending who have asked for this. Thanks  

I have searched for a way to show sign in codes in plan text rather than obscured. I seem to remember that used to be possible, but no longer with the latest version.
I would suggest that you implement a way to un-obscure the values with the action controlled by the key user sign-in. Perhaps a right click would be a neat way?

We have discovered a problem in one recent natch of Speaker Overlay (the silver overlay covering the speaker) has weak adhesive and comes off easily.

We have remedied the problem at the factory
If you have this problem, you can send it for repair, or you can use any adhesive to secure the speaker overlay to the base.
Our apologies for this problem

Dear all, 
Because kt03 has already discontinued, any want to sell it ? At mint condition .
Best regards

Hi,
Many thanks for your help previously with my RS485 issue. Issue is now resolved per your advice and Gary Morgan. System working well. I am planing going to Economy 10 electricity tariff.  This gives 10 hours of cheaper electricity during the day - there are 3 periods . However the meter is timed with  UTC time and does not change with Summer Time changes.
Via MOD BUS TCP interface with the Victron solar battery inverter and charger I want to control when the battery is charged (if not enough solar) so that the Grid charges the battery during the cheaper periods and then discharges during the more expensive time periods.
I have tested the Comfort MODBUS TCP interface with the Victron unit and this works.
The issue is how to manage UTC. I do not want switch off the time synching via ETH03 as this set all my time programs for Heatmiser and DHW etc.
How would you go about setting up time programs in this case?
The Time period below are UTC.

1. Three off-peak hours in the afternoon (e.g. 1pm – 4pm)Two in the evening (e.g. 8pm – 10pm)Five overnight (e.g. midnight – 5am)

I have a set of curtains controlled by a Cbus Shutter Relay (L5501RBCP). I can control this by means of the two following Responses.
CloseCurtains - Cbus Off UCNBus 54 ! Close Curtains
OpenCurtains - Cbus On UCNBus 54 ! Open Curtains
These Responses operate the curtains if executed from the .cclx file or by means of Time Programs set  up in the Scedule Section
I also set up a further Response to test the Sunset operation as follows
NightCurtainClos - If Night Time <> 0 Then
Do CloseCurtains ! Close Curtains
End If
This Response can be executed from the .cclx file at times after the local Sunset time as in the Schedule Section but will not close the curtains automatically.
Is there something fundamental I am doing wrongly

Cytecch\'s Logic Controllers have been designed as Automation Controllers, similr to Comfort CM9000/9001 but with the Alarm, Voice, Telephone Dial-out features.

LGX01 Logic Engine has 8 inputs and 8 Outputs expandable to 96 Inputs and Outputs, using Slave Expansion and Local Expansion Modules


UCM/Logic Controller is similar to LGX01 Logic Engine, but it does not have any Inputs and Outputs



Photos are not to scale

Both LGX01 and UCM/Logic have Responses, Counters, Flags, Sensors, Time Programs. They can be connnected to all the Comfort UCM Interfaces including USB, Ethernet, KNX, Cbus, Velbus, Modbus, and other Cytech modules like IRIO (Remote Input/Output Module), MSM01 Multi-sensor Module (temperature/Humidity) , HIO Hotel Input/Output, Temperature Sensor.
Power Supply is 12V 1 Amps
These 2 products are powerful low cost products suitable for automation applications

We have not been making any updates to Velbus for a number of years due to various reasons
However, we have decided to update the firmware to support many of the new Velbus products.

This will require a new Beta firmware and a new Comfigurator version, probably 3.12.8
As we do not have access to most of the new Vebus products, we would appreciate if the existing UCM/Vlebus users could try it out when available
We are working on the testing of the Velbus firmware and Comfigurator

recently the Audio confirmation, e.g. \"Night mode\" ceased on the system. As a first step I decided to look at the logs rather than diving into the alarm box and checking the speaker wiring, which I think was the right decision.
I upgraded the configurator to 3.12.7.0 and, incidentally, it gives an \"Unhandled exception\" error whenever you click on a topic in the left hand window. (Windows 10 32 bit fairly up-to-date) It said there was a module error (I presume in comfort) and updated that and then I was able to download the log. (Pity it doesn\'t paginate so you can print off the last 50 entries or so.) 
What I spotted was that a recent entering of my unlock code to see if would clear things triggered the following sequence.
DSP/Voice fail 96. 
DSP/Voice Restore 97. 
Reset 97. 
After this audio was restored.
Where can I find this in comfort? are they action codes or responses. Where can I find a description of what is going on? Is something failing? should I take action? Why did entering the user code fix things this time but previously had not fixed things.
Any pointer to documentation or answers would be appreciated.

Attached Files

Thumbnail(s)
   

The KP04 has another mode, when connected to CM9001-EMS Environmental Monitoring System. This is described here
http://www.comfortforums.com/forum139/4912.html