Important
Please do NOT lay the Keypad wires close to any Mains Cable, as this will cause interference in the form of a loud humming or buzzing. This noise is almost impossible to  remove except  by moving the keypad wires AWAY from the Mains cable. 50/60 Hz is in the voice frequency range and is difficult to filter out

It is also importrant to use CAT 5 cable preferably shielded

I have a Comfort II and am doing some reconfiguration.I want to Force Arm (arm the system with open zones) using a response. I have had this working in the past but not at the moment.I am using the response ForceArm, the underlying codes being 17, 255I have \'Allow Force Arm\' ticked as Yes in Security Configuration Flags.If I execute the response nothing happens.The I/o monitor shows;>
LI****
< LU01
> DT
< DT2016112900313300
> EL
< EL11FFFFFFFFFF
> f?00
> Y?
> Z?
> z?
> M?
> K?
> a?
> DA11FF
< f?000100000000000000000000000000000000000000000000000000000000000000
< Y?0000
< Z?250000
< z?000000000000000000000000000000
< M?0001
< KL00010000
< a?000000000000000000
< RA0000
Any suggestions as to why this isn\'t working?

Hi,
I have 4 scs switches, but two of them are no longer used so I need to remove them from my configurataion. I go to modules and settings, delete the removed ones, and then do a selective upload to update modules and setting.
However, once I do this, and then do a scan for all modules, comfort still detects 4 scs switches, even though two are removed, so it should only detect the remaining two ?
Would appreciate some quick advice on this, heading away tomorrow, so just want to get the comms failure cleared.
Regards,Eamon

Hi,

A few days ago my comfort II systems started announcing \"zero\" repeatedly. I did a system reset, and the received a \"wrong text\" displayed on my KP06s. I did a vocabulary/sentence/LCD date upgrade and the system is now back to normal, except that all the zones are displayed and announced by their zone number, i.e. Zone 1, instead of front door.

I am not sure how to resolve this, and would appreciate any assistance.

Thanks,
Iain

The Action \"Limit Dialout\" in the Alarm Response will allow dial out only to the selected phones or None


You can have a different response for each alarm, thus to disable the dial out or dial to certain numbers depending on any condition,
eg
If Security Mode = Night
 Limit Dialout 0

I hate waking up other members of the family whose numbers are programmed into my system when one of us comes downstairs at say 03:00hrs half-asleep and totally forgets that there is a alarm system to turn off!
Is there a way to omit dial-out on all numbers when Comfort is set to night mode?
ALSO
Can this done selectively - by alarm type?
(it would be sensible if a fire alert DID cause a dial out)
AND
second related question. How do I stop Comfort from dialing out once it has started?

One of the issues I have with my installation is terminating all the +12V & gnd connections that feed to the detectors. I have about 12 pairs of cable all attempting to go into one screw down/push on connector. This is obviously not possible so I have extended the 12V output by daisy-chaining a series of screw terminal \'chop-block\' connectors. This works but is not something I am NOT very proud of + I feel it is not reliable, I\'d be interested to learn what others have done to deal with this issue
AND
Cytech - please could you let me know the make and type of the push on terminals - the one\'s in the attached image.
Thank you

Attached Files

Thumbnail(s)
   

[size=\"3\"]Q1/.
On reading the instructions for my newly acquired UCM/USB:
Page 5 of ucmman state \"...up to 100 meters, use a cable with 3 twisted pairs. 12V/GND, KA/KB are to be paired with one pair as spare\"
I\'d like to confirm how these connections should be made.
As I read it (admittedly late at night )[/size]

1. [size=\"3\"]12V&amp;KA are linked - at both ends?
   [/size]
2. [size=\"3\"]GND&amp;KB are linked - at both ends?
   and the third pair are
   [/size]
3. [size=\"3\"]A &amp; B which are connected respectively at each end
   [/size]

ETH03 firmware 2.20 has a bug when UCM/ETH03 is used to Upgrade Vocabulary. The Vocab upgrade gets stuck at arounn 9%.
UCM Monitor IO will show as below;

> VL48C0202431175358AA5F8B26995213F62CAA2856F4E567835BCA905E8B16A472AFD9E4C6
< OK
> VL48E02075F1A2AA42CB2BD1DC345F9016A58E35579BCE9AE495C4C886C0664A5FA426A959
< OK
> VL490020862DD74D42132B69292C73556CED5C26278D5CD1197B9E00A114E013AAF204AADA
< OK
> VL492020654CF09EAA4F7824320B4A67B05D794F48E2594B52A36CF1779C3263554F41DB58
< OK
> VL494020A4AD3457729E7258C98E487C2E49F2DB51EA39C181EE6AD170845570C8640DF67B
< NA
> LI
< LU00
!


 Please upgrade ETH03 firmware to 2.23

see http://www.comfortforums.com/forum113/3820.html for how to upgrade ETH03 firmware

The new 1.2 version of the Comfort iOS app has been released
For new users, look for Cytech Comfort in the Appstore

Bugs

• Saved User code does not work for Local Connection 2
• Logging in to 2nd port eg 1002 actually logs into the 1st port eg 1001 so the 2nd port is not being used
  

• Selectable 2 ports for Local and 2 ports for Remote on the log in page so if one  port is busy, the other port can be selected quickly
  
• Added user-selectable Icons for Control appliances with status change
  
• Removed click sounds when control button is pressed